jona29
Newbie
Karma: +1/-1
 Offline
Posts: 22
|
 |
« Reply #255 on: February 23, 2013, 02:51:05 PM »
|
|
|
thankyou so much for your patience ddlillinger i was missing the sum after the file name ,edited the bin and mirrored the skc and corrected the checksum .
just have to reflash it to the ecu tomorrow
managed to flash eeprom today didnt have the correct plug just used a set of croc leads from maplin .
car now runs
many thanks dd
|
|
|
|
« Last Edit: February 25, 2013, 08:43:43 AM by hollow »
|
Logged
|
|
|
|
ChrisselSchissel
Newbie
Karma: +0/-0
Offline
Posts: 2
|
|
« Reply #256 on: March 06, 2013, 01:29:28 PM »
|
|
|
Hey,
i've some problems with flashing in bootmode...
so problem is that i can't read anything on ecu with bootmode. in normal mode everything works fine..
the errors are: "no response from ecu (0x08)" and "bootmode ... fail (0x07)
I supply the ecu with ~13,5V and grounded pin 24 for the first 2-3 seconds after switching on the system.
The cable i use is a normal OBD-cable with RS323 and KL-line support. A friend of mine means that this is working fine at hims setup..
|
|
|
|
|
Logged
|
|
|
|
KWest
Newbie
Karma: +0/-0
Offline
Posts: 9
|
|
« Reply #257 on: March 13, 2013, 10:12:35 PM »
|
|
|
Using 1.40 on a ME7.1.1 in a RS6 I get errors: 0x501010 and 0x21007.
command line args : ME7EEPROM --OBD -r -p 1 rs6orgin.bin
I have tried cycling the key before running, connecting with VCDS and then running, turning key on with trying to connect.
Any tips? I just bought the car and would like to backup the EEPROM before I try read the flash.
Thanks in advance.
|
|
|
|
|
Logged
|
|
|
|
ddillenger
Moderator
Hero Member
Karma: +639/-21
Offline
Posts: 5640
|
|
« Reply #258 on: March 13, 2013, 10:16:07 PM »
|
|
|
I get a lot of x07 errors with OBD on 7.1.1. Bootmode the eeprom, it'll read just fine.
|
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
tbm
Full Member
Karma: +2/-1
Offline
Posts: 176
|
|
« Reply #259 on: March 14, 2013, 03:46:52 AM »
|
|
|
Hi Guys, I'm noob in flashing ME7.5 that's why don't kick me a lot for my dump questions  I want to swap my ECU M3.8 to ME7.5 (photo is below) (AUQ engine). As far as I understood my first action should defeat IMMO in the new ECU (ME7.5). According to this could someone explain or give me the URL with explanation which pins I should use in ECU in order to read/write my ECU "on the table" with the mentioned programm not in the car through OBD? Thanks in advance!  Regards, Oleg |
|
|
|
|
Logged
|
|
|
|
cyril279
Full Member
Karma: +12/-2
Offline
Posts: 140
|
|
« Reply #260 on: March 14, 2013, 04:35:08 AM »
|
|
|
|
|
|
|
|
Logged
|
|
|
|
tbm
Full Member
Karma: +2/-1
Offline
Posts: 176
|
|
« Reply #261 on: March 14, 2013, 05:51:14 AM »
|
|
|
Thanks a lot!!! That is what I wanted. |
|
|
|
|
Logged
|
|
|
|
sweegie
Full Member
Karma: +10/-2
Offline
Posts: 137
|
|
« Reply #262 on: March 16, 2013, 11:16:17 AM »
|
|
|
I get a lot of x07 errors with OBD on 7.1.1. Bootmode the eeprom, it'll read just fine.
Or you can use K+CAN commander 2.5 to read the eeprom too  |
|
|
|
|
Logged
|
|
|
|
ddillenger
Moderator
Hero Member
Karma: +639/-21
Offline
Posts: 5640
|
|
« Reply #263 on: March 16, 2013, 11:17:26 AM »
|
|
|
Or you can use K+CAN commander 2.5 to read the eeprom too I fell in love with the speed at which I can do things in CMD as opposed to cumbersome GUI's. Never thought that would happen |
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
AWAS
Newbie
Karma: +0/-0
Offline
Posts: 6
|
|
« Reply #264 on: March 24, 2013, 10:52:04 AM »
|
|
|
Good day! I have ECU 4b0906018CM (working KWP2000). Soft dont work. C:\Users\Nika>D:\auto\soft\Nefmoto\me7_95040_1_31.exe --OBD -p2 --screen
Ver: 1.31
Com Port: 2
Baud Rate: 10400
Opening COM2 ... OK
Initiating communication ... FAIL. (error=0x01)
Closing COM2
I think it's in the protocol. Is there a solution to this issue? |
|
|
|
|
Logged
|
|
|
|
ddillenger
Moderator
Hero Member
Karma: +639/-21
Offline
Posts: 5640
|
|
« Reply #265 on: March 24, 2013, 10:56:51 AM »
|
|
|
Good day!
I have ECU 4b0906018CM (working KWP2000).
Soft dont work.I think it's in the protocol.
Is there a solution to this issue?
Try bootmode. Whenever I have a problem reading, I use bootmode. 1/10th the time, and always works. |
|
|
|
|
Logged
|
Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience!
Email/Google chat:
DDillenger84(at)gmail(dot)com
Email>PM
|
|
|
AWAS
Newbie
Karma: +0/-0
Offline
Posts: 6
|
|
« Reply #266 on: March 24, 2013, 11:11:02 AM »
|
|
|
Try bootmode. Whenever I have a problem reading, I use bootmode. 1/10th the time, and always works.
Thank you, and do it! |
|
|
|
|
Logged
|
|
|
|
tbm
Full Member
Karma: +2/-1
Offline
Posts: 176
|
|
« Reply #267 on: March 29, 2013, 01:40:06 AM »
|
|
|
ArgDub thanks a lot! Your programm is very nice! I've managed to read EEPROM from my ECU in bootmode. But now I have some new questions 1. Can I leave 2kOm resistor soldered to flash chip for always? I've noticed that I could connect to ECU with bootmode in several second after switch +12B. 2. As I understood I can only EEPROM read/write with this programm? Regards, Oleg
|
|
|
|
|
Logged
|
|
|
|
player
Full Member
Karma: +1/-5
Offline
Posts: 128
|
|
« Reply #268 on: April 08, 2013, 09:06:05 AM »
|
|
|
hello..great program!
i have a problem..i can read the 95040 from my 8n0 906 018 S but i can't write..i keep getting this error...what can i do?thanx!
|
|
|
|
|
Logged
|
|
|
|
player
Full Member
Karma: +1/-5
Offline
Posts: 128
|
|
« Reply #269 on: April 08, 2013, 11:17:32 AM »
|
|
|
i managed to write without error the immo off file.but i dont get one thing...i have a 8n0 906 018 S ecu..if i write the 8n0 906 018 A flash in it ( both are 29f400bb) , vag-com doesnt recognize the ecu anymore....why?
thanx in advance!
|
|
|
|
|
Logged
|
|
|
|
|
