Noob Question for 8L0906018N SAI N80 delete

Pages: [1]

« previous next »

Author

Topic: Noob Question for 8L0906018N SAI N80 delete (Read 1052 times)

AllaNoN

Newbie

Karma: +0/-0
Offline

Offline

Posts: 6

	Noob Question for 8L0906018N SAI N80 delete « on: November 17, 2023, 08:13:57 AM »

Hello together.
First of all,
this Forum was a huge Information Helper when i started my 1.8t Project.

I´ve done the read out of the 1.8t apy s3 ECu, also with immo off.

Alone for this massive input which i´ve found here a huge Thank you to the Forum.

Now i´m asking myself, before writing my File back, was everything correct what i did ?!

original File and changed File is attached.
this is with the "wrong" filesize cause 512KB wasn´t read. correctly from ecu (known problem with nefmoto i think?!)
I´ve tried to do SAI off, N80 off via eskonf
also did the change in the MSLUB and MLSUS to 0
CWKONABG changed from 0.00 to 4 i think must be correct ?

and the CW_CAN_R is from 4 to 0 cause the ECu will work in a golf mk2
and corrected the memory from readout cause it only has 512KB in ECU.

Did i oversee something in my baby steps ?

Thanks in advance


	Logged

_nameless

Hero Member

Karma: +326/-451
Offline

Offline

Posts: 2717

	Re: Noob Question for 8L0906018N SAI N80 delete « Reply #1 on: November 18, 2023, 02:13:42 AM »

Quote from: AllaNoN on November 17, 2023, 08:13:57 AM

You used the wrong memory layout when reading abd that's why it's the wrong size


	Logged

If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/

AllaNoN

Newbie

Karma: +0/-0
Offline

Offline

Posts: 6

	Re: Noob Question for 8L0906018N SAI N80 delete « Reply #2 on: November 19, 2023, 04:25:10 AM »

Thanks, beside from the fact that i used the wrong layout in first place, is the rest correct !?

Cause i´m asking me why in eskfonig the z coils the values are 11.
the apy has regular ignition coils without the Ignition Control Module
But why are there Values of 11 instead of what i thought 00 ??

from the original one Adress to change should be 00014F10

Code:

## ESKONF_0 (Addr:00014F10) -- FF FF 00 C0 FF F8 33
b0:FF    ZUE4(95)..:N(11)    ZUE3(94)..:N(11)    ZUE2(103).:N(11)    ZUE1(102).:N(11)   ZUE=Ignition coil
b1:FF    NC........:N(11)    NC........:N(11)    NC........:N(11)    NC........:N(11)
b2:00    EV4(89)...:Y(00)    EV3(88)...:Y(00)    EV2(97)...:Y(00)    EV1(96)...:Y(00)   EV=Fuel injector
b3:C0    LSHHK(63).:N(11)    EFLA(48)..:Y(00)    LDR(104)..:Y(00)    TEV(64)...:Y(00)   LSHHK=Rear O2, EFLA=Error lamp, LDR=N75, TEV=N80 purgevalve
b4:FF    BKV(22)...:N(11)    NC(24)....:N(11)    AAV(116)..:N(11)    MIL(47)...:Y(00)   BKV=Brakebooster pump, AAV=Shutoff valve, MIL=OBD lamp
b5:F8    NC........:N(11)    NC........:N(11)    EKP(65)...:S(10)    SLP(66)...:Y(00)   EKP=Fuel pump, SLP=J299 SAI pump
b6:33    ULT(105)..:Y(00)    UAGR(114).:N(11)    SLV(9)....:Y(00)    NWS(115)..:N(11)   ULT=N249 wg valve, UAGR=EGR valve, SLV=N112 SAI relay, NWS=n205 VVT

## ESKONF_1 (Addr:0002908D) -- FF FF 00 F0 3F F0 2C
b0:FF    ZUE4(95)..:N(11)    ZUE3(94)..:N(11)    ZUE2(103).:N(11)    ZUE1(102).:N(11)   ZUE=Ignition coil
b1:FF    NC........:N(11)    NC........:N(11)    NC........:N(11)    NC........:N(11)
b2:00    EV4(89)...:Y(00)    EV3(88)...:Y(00)    EV2(97)...:Y(00)    EV1(96)...:Y(00)   EV=Fuel injector
b3:F0    LSHHK(63).:N(11)    EFLA(48)..:N(11)    LDR(104)..:Y(00)    TEV(64)...:Y(00)   LSHHK=Rear O2, EFLA=Error lamp, LDR=N75, TEV=N80 purgevalve
b4:3F    BKV(22)...:Y(00)    NC(24)....:N(11)    AAV(116)..:N(11)    MIL(47)...:Y(00)   BKV=Brakebooster pump, AAV=Shutoff valve, MIL=OBD lamp
b5:F0    NC........:N(11)    NC........:N(11)    EKP(65)...:Y(00)    SLP(66)...:Y(00)   EKP=Fuel pump, SLP=J299 SAI pump
b6:2C    ULT(105)..:Y(00)    UAGR(114).:S(10)    SLV(9)....:N(11)    NWS(115)..:Y(00)   ULT=N249 wg valve, UAGR=EGR valve, SLV=N112 SAI relay, NWS=n205 VVT

## ESKONF_2 (Addr:00094F10) -- FF FF 00 C0 FF F8 33
b0:FF    ZUE4(95)..:N(11)    ZUE3(94)..:N(11)    ZUE2(103).:N(11)    ZUE1(102).:N(11)   ZUE=Ignition coil
b1:FF    NC........:N(11)    NC........:N(11)    NC........:N(11)    NC........:N(11)
b2:00    EV4(89)...:Y(00)    EV3(88)...:Y(00)    EV2(97)...:Y(00)    EV1(96)...:Y(00)   EV=Fuel injector
b3:C0    LSHHK(63).:N(11)    EFLA(48)..:Y(00)    LDR(104)..:Y(00)    TEV(64)...:Y(00)   LSHHK=Rear O2, EFLA=Error lamp, LDR=N75, TEV=N80 purgevalve
b4:FF    BKV(22)...:N(11)    NC(24)....:N(11)    AAV(116)..:N(11)    MIL(47)...:Y(00)   BKV=Brakebooster pump, AAV=Shutoff valve, MIL=OBD lamp
b5:F8    NC........:N(11)    NC........:N(11)    EKP(65)...:S(10)    SLP(66)...:Y(00)   EKP=Fuel pump, SLP=J299 SAI pump
b6:33    ULT(105)..:Y(00)    UAGR(114).:N(11)    SLV(9)....:Y(00)    NWS(115)..:N(11)   ULT=N249 wg valve, UAGR=EGR valve, SLV=N112 SAI relay, NWS=n205 VVT

## ESKONF_3 (Addr:000A908D) -- FF FF 00 F0 3F F0 2C
b0:FF    ZUE4(95)..:N(11)    ZUE3(94)..:N(11)    ZUE2(103).:N(11)    ZUE1(102).:N(11)   ZUE=Ignition coil
b1:FF    NC........:N(11)    NC........:N(11)    NC........:N(11)    NC........:N(11)
b2:00    EV4(89)...:Y(00)    EV3(88)...:Y(00)    EV2(97)...:Y(00)    EV1(96)...:Y(00)   EV=Fuel injector
b3:F0    LSHHK(63).:N(11)    EFLA(48)..:N(11)    LDR(104)..:Y(00)    TEV(64)...:Y(00)   LSHHK=Rear O2, EFLA=Error lamp, LDR=N75, TEV=N80 purgevalve
b4:3F    BKV(22)...:Y(00)    NC(24)....:N(11)    AAV(116)..:N(11)    MIL(47)...:Y(00)   BKV=Brakebooster pump, AAV=Shutoff valve, MIL=OBD lamp
b5:F0    NC........:N(11)    NC........:N(11)    EKP(65)...:Y(00)    SLP(66)...:Y(00)   EKP=Fuel pump, SLP=J299 SAI pump
b6:2C    ULT(105)..:Y(00)    UAGR(114).:S(10)    SLV(9)....:N(11)    NWS(115)..:Y(00)   ULT=N249 wg valve, UAGR=EGR valve, SLV=N112 SAI relay, NWS=n205 VVT


« Last Edit: November 19, 2023, 04:43:45 AM by AllaNoN »	Logged

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

May 21, 2024, 08:27:47 AM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search