|
Title: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: mcgas001 on May 25, 2012, 03:11:04 AM Edit
Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: mcgas001 on May 25, 2012, 07:35:18 AM edit
Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: mcgas001 on May 25, 2012, 11:04:30 PM Bump - Anyone got any ideas?
Noticed that the overboost is still there, seems a lot more controlled tho. One of the maps seems to have reeled it in a bit, and the other has bought it back again. Gonna tweak one to 50% and see the difference then go from there. Will be handy to see how they react on the car. Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: Rick on May 26, 2012, 02:26:29 PM KFLDRL should be left std unless you are exceeding the MAP limit.
Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: littco on May 26, 2012, 03:00:39 PM I don't know if it's any help but the vrx k04 is very similar to the hybrid s3 turbos. These produce boost around 3k incredibly quickly so guess its very Easy to over shoot. Also I found I had to reduce kfldrl down to around 10% in order to open the wastegate and control boost successfully at wot it was set at about 50 opposed to being 95% on a stick actuator.
But I will say I ended up running an MBC in parallel to cap the spikes as I haven't managed to curb them. Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: fredrik_a on May 26, 2012, 10:44:10 PM Is there a limit to how many times you can map an ECU? Theoretically yes, the IC supplier (of an MCU/Eeprom etc) often specifies a minimum or typical number of flashes. Practically though... The number of programming sequences allowed is usually far more than you would ever need. Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: mcgas001 on May 27, 2012, 05:44:27 AM edit
Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: littco on May 27, 2012, 06:23:42 AM All I'd say is go with rick! I trust him more than myself, I'm only going on my own experience where as rick is the pro.
I know for sure though I had to adjust kfldrl when I fitted an uprated actuator the cracking pressure is more so you need less dc to open it. Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: Lobuziak on May 28, 2012, 03:53:56 AM I have made a comparison of different KFLDRL maps for Z20Lex. It looks like S2.5 uses stronger actuator on VXR turbo. Take a look, it can help You with mods. Added LDRXN comparison too...
Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: mcgas001 on May 31, 2012, 04:49:30 AM edit
Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: mcgas001 on May 31, 2012, 07:26:33 AM edit
Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: prj on May 31, 2012, 07:37:39 AM You need to re-do your entire KFLDRL map if you changed to a stronger wastegate.
You also need to make sure that requested boost is not lower than the boost provided by the wastegate at any point. Read this topic, on how to properly configure it from scratch: http://www.nefariousmotorsports.com/forum/index.php?topic=517.10 (http://www.nefariousmotorsports.com/forum/index.php?topic=517.10) Until you do this, your boost control will be all over the place. Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: mcgas001 on May 31, 2012, 07:40:31 AM edit
Title: Re: Mapping Limit (ME1.5.5)? + Other Questions.. Post by: mcgas001 on May 31, 2012, 03:17:32 PM edit
|