Ok i've had problem with system separators i guess, after set it up properly to decimal dot instead sheet works now.
Uploading updated sheet and Polynomial Equation seems to work but still i don't know if it is proper scaled if anyone could take a look.
Red KG/h is rescaled by Polynomial Equation based on Stock MAF.
Yellow is adjusted by hand so i could drive the car.
Blue marked cells 230kg/h seems to be my Stable Idle point that i hold on to.
Gonna test Red scaling in car, any help would be appreciated thanks.
|
1
on: Today at 09:32:43 AM
|
||
| Started by Fabioo - Last post by Fabioo | ||
|
2
on: Today at 09:06:23 AM
|
||
| Started by BenR - Last post by agron25 | ||
|
up
 |
||
|
3
on: Today at 05:46:04 AM
|
||
| Started by fredrik_a - Last post by s90power | ||
|
TYPO IN MY FILE NAME the "WinOLS (Volvo S60 R auto (Original) - 359462) 50GPHJ.xdf " is actually an 50QKHJ ------------------------------------------------------------------------------------------- ik some are the same SW version but they have different use cases. i should have merged them so theres not like 4214235 different gphj but i did it quick. to check can always side by side with ols but should be good I have read through this thread and learned a lot, Thanks everyone. Only thing that I cannot find in my own file is the consumption constant KVB. I have attached my original file if someone is willing to help out |
||
|
4
on: Today at 04:49:56 AM
|
||
| Started by JeanAwt - Last post by JeanAwt | ||
|
hi, I tested wot because I wonder if the problem doesn't come from elsewhere. probe 02, however recent. I tested the tvub I ran for 15min...same bounce 760/840rpm group 32 0 adaptation 33 bounce -13/-18 at 1,500/1,540v I will do other tests when I have more time. thank you
|
||
|
5
on: Today at 03:19:14 AM
|
||
| Started by Den_95 - Last post by Den_95 | ||
|
And you have posted zero information about your software, nor have you uploaded a file, do you think you landed on a magicians forum where people can help you without any information? The forum does not skip a file larger than 2.5 Mb. The OEM bin file weighs 3.4 MB. What should I do? SC800H1400000_8T2907115A_0002 |
||
|
6
on: Today at 02:55:51 AM
|
||
| Started by why - Last post by IamwhoIam | ||
|
Sorry but what is SIMOLS18??? It's a new ECU from ContiMental  |
||
|
7
on: Today at 02:55:03 AM
|
||
| Started by Den_95 - Last post by IamwhoIam | ||
|
And you have posted zero information about your software, nor have you uploaded a file, do you think you landed on a magicians forum where people can help you without any information?
|
||
|
8
on: Today at 02:42:42 AM
|
||
| Started by Den_95 - Last post by Den_95 | ||
|
Yes it's totally unclear to anyone what you're talking about. I need a damos file for my software. |
||
|
9
on: Today at 02:00:16 AM
|
||
| Started by why - Last post by S2evo1 | ||
|
I increased the set pressure and pressure ratio limits, scaled "ip_maf_stk_sp_vvl_cam" and "ip_tqi_ref_n_m_air_vvl_cam" accordingly, increased the clutch torque limit, and the supercharger speed limit. I don't see the set boost in the logs. The improvement, I don’t know where the error is! Can anyone help me analyze it? grateful! Sorry but what is SIMOLS18??? |
||
|
10
on: Today at 12:33:34 AM
|
||
| Started by Den_95 - Last post by IamwhoIam | ||
|
Yes it's totally unclear to anyone what you're talking about.
|
||