|
nyet
|
 |
« Reply #90 on: April 13, 2020, 12:00:17 PM »
|
|
|
This was assumption, as the difference with k04 is huge regarding pull even tho im driving with base boost.
From the info i have found the safe point is 300tq
A single K04 can't do much more than 200-250 anyway |
|
|
|
|
Logged
|
|
|
|
|
BlackT
|
|
« Reply #91 on: April 13, 2020, 12:32:41 PM »
|
|
|
But it can still cause damage
K04-015 with a shities tune I have ever seen
BFB engine
|
|
|
|
« Last Edit: April 13, 2020, 12:47:08 PM by BlackT »
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #92 on: April 13, 2020, 12:40:53 PM »
|
|
|
But it can still cause damage
K04-001 with a shities tune I have ever seen
BFB engine
from detonation or too much tq? |
|
|
|
|
Logged
|
|
|
|
K92
Full Member
Karma: +0/-3
 Offline
Posts: 137
|
|
« Reply #93 on: April 13, 2020, 12:48:24 PM »
|
|
|
Anyway, i have read on this forum, where some member, had gt2860rs on his 1.8t with stock rods , prj incl others told that he had probably already bent rods, so that made me cautious. If the difference is so big compared to k04, wont be impossible i think.
|
|
|
|
|
Logged
|
|
|
|
xsix
Jr. Member
Karma: +0/-2
Offline
Posts: 32
|
|
« Reply #94 on: April 13, 2020, 12:53:48 PM »
|
|
|
Especially too much torque at low engine speed damage stock rods. How spool your turbo ?  |
|
|
|
|
Logged
|
|
|
|
|
BlackT
|
|
« Reply #95 on: April 13, 2020, 12:57:09 PM »
|
|
|
I would say no detonation looking at piston, but cant be sure beacuse scrap from piston skirt has damaged top of piston. File was stock, only: underscaled MAF, LDRXN/LDRXNK in all area 255, KFMIRL same 255, and little work on KRKTE And all that on 95 octane When i made log it was -12 retard all time during WOT  |
|
|
|
|
Logged
|
|
|
|
K92
Full Member
Karma: +0/-3
Offline
Posts: 137
|
|
« Reply #96 on: April 13, 2020, 01:11:34 PM »
|
|
|
Especially too much torque at low engine speed damage stock rods. How spool your turbo ? I will find my balls tomorrow and log WOT with 3rd. If im not mistaken, 3100rpm - 3300rpm =1bar |
|
|
|
|
Logged
|
|
|
|
K92
Full Member
Karma: +0/-3
Offline
Posts: 137
|
|
« Reply #97 on: April 14, 2020, 10:13:07 AM »
|
|
|
So here is my afr after today run. Ofc i run out of maf at the end, but before changing to bigger one i would like to dial the fuel with this maf. Is thiss considered rough ? Is this fixable in HFM ?( dont mind after 5000k, thats where maf is 5V )
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #98 on: April 14, 2020, 10:20:14 AM »
|
|
|
hard to tell w/o stfs lambda control values.
|
|
|
|
|
Logged
|
|
|
|
K92
Full Member
Karma: +0/-3
Offline
Posts: 137
|
|
« Reply #99 on: April 14, 2020, 10:22:26 AM »
|
|
|
hard to tell w/o stfs lambda control values.
Sorry i forgot whole log. |
|
|
|
|
Logged
|
|
|
|
xsix
Jr. Member
Karma: +0/-2
Offline
Posts: 32
|
|
« Reply #100 on: April 14, 2020, 11:39:32 AM »
|
|
|
wrong log file  |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #101 on: April 14, 2020, 11:44:00 AM »
|
|
|
Sorry i forgot whole log.
That log sure doesn't look good |
|
|
|
|
Logged
|
|
|
|
K92
Full Member
Karma: +0/-3
Offline
Posts: 137
|
|
« Reply #102 on: April 14, 2020, 11:45:42 AM »
|
|
|
This is right one. Sorry
|
|
|
|
|
Logged
|
|
|
|
xsix
Jr. Member
Karma: +0/-2
Offline
Posts: 32
|
|
« Reply #103 on: April 14, 2020, 12:06:36 PM »
|
|
|
How you control boost ? oem n75 or external controller ?
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #104 on: April 14, 2020, 12:07:25 PM »
|
|
|
How you control boost ? oem n75 or external controller ?
There is no good reason to use an external controller. I should hope he's not that silly. |
|
|
|
|
Logged
|
|
|
|
|
