mdccode5150
Full Member
Karma: +12/-4
Offline
Posts: 122
|
|
« on: November 22, 2020, 11:29:19 PM »
|
|
|
I have some Hybrid ECU's that came out of a Saturn L300, and a Cadillac CTS 3.2L, and wanted to see if I could read the EEPROM, and readout the EPROM. I tried me7-eeprom-1.40 in boot mode (no go) and my tech2, and couldn't read with either. I used a harness plug to make a jig, and statically checked the pinout with the schematic and all good. I tried a couple of them. I use the ME7.3.1 pinout and ground pin #20. Can anyone help?
|
|
|
Logged
|
|
|
|
gremlin
|
|
« Reply #1 on: November 23, 2020, 03:14:45 AM »
|
|
|
I use the ME7.3.1 pinout and ground pin #20. Can anyone help?
Why did you choose this type? AFAIK GM vehicles have never used ME7.3.1 ecus. Please provide exact Bosch part number 0 261 xxx xxx then we can determine the type of ECU.
|
|
|
Logged
|
|
|
|
_nameless
|
|
« Reply #2 on: November 23, 2020, 07:54:38 AM »
|
|
|
I tried me7-eeprom-1.40 in boot mode (no go)
that eeprom tool is for vag only
|
|
|
Logged
|
If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/
|
|
|
prj
|
|
« Reply #3 on: November 23, 2020, 07:59:15 AM »
|
|
|
that eeprom tool is for vag only
And it definitely doesn't work with a tech 2 lol
|
|
|
Logged
|
|
|
|
mdccode5150
Full Member
Karma: +12/-4
Offline
Posts: 122
|
|
« Reply #4 on: November 27, 2020, 02:49:38 PM »
|
|
|
that eeprom tool is for vag only
I believe your correct (The Pinouts are the same, and I took the plastic cap off one and it looked the same, but the casting number is not). Here are some pictures of some off the ecu's I have.
|
|
|
Logged
|
|
|
|
mdccode5150
Full Member
Karma: +12/-4
Offline
Posts: 122
|
|
« Reply #5 on: November 27, 2020, 02:58:11 PM »
|
|
|
The first one is the Saturn/Catera/CTS ECU 2nd Cadillac 3.6L 3rd Saab 2.8T
|
|
|
Logged
|
|
|
|
mdccode5150
Full Member
Karma: +12/-4
Offline
Posts: 122
|
|
« Reply #6 on: November 27, 2020, 03:04:02 PM »
|
|
|
And one more showing casting numbers and part numbers.
|
|
|
Logged
|
|
|
|
mdccode5150
Full Member
Karma: +12/-4
Offline
Posts: 122
|
|
« Reply #7 on: November 27, 2020, 10:32:55 PM »
|
|
|
Found intermittent connection/switch on my plug adapter...Now communication is working and can pull codes. I'm crossing my fingers, and will be testing boot mode.
|
|
|
Logged
|
|
|
|
gremlin
|
|
« Reply #8 on: November 28, 2020, 12:28:35 AM »
|
|
|
I'm crossing my fingers, and will be testing boot mode. Read tech docs first... ME9.6 ECU use Freescale MPC5xx processors family. This MCU does not have boot mode at all. It use BDM port for full access to internal memory. It will looks like on the picture.
|
|
« Last Edit: November 28, 2020, 12:31:03 AM by gremlin »
|
Logged
|
|
|
|
mdccode5150
Full Member
Karma: +12/-4
Offline
Posts: 122
|
|
« Reply #9 on: November 28, 2020, 11:51:02 AM »
|
|
|
Thanks. I think I can work with the ME9.6 using software from these guys: https://txsuite.org/And I pulled the plastic cover off of the Saturn and on the ceramic board it says ME76ZP-A It looks similar to the ME7.3.1 but there are (2) chips that are not installed on the board and some resistors that are configured differently.
|
|
|
Logged
|
|
|
|
mdccode5150
Full Member
Karma: +12/-4
Offline
Posts: 122
|
|
« Reply #10 on: November 28, 2020, 11:54:40 AM »
|
|
|
Here is a ME7.3.1
|
|
|
Logged
|
|
|
|
mdccode5150
Full Member
Karma: +12/-4
Offline
Posts: 122
|
|
« Reply #11 on: November 28, 2020, 12:35:33 PM »
|
|
|
Here is the newer version 0 261 206 509 the main chips are different, and some very minor resistor changes. The older versions above are 0 261 204 591.
|
|
|
Logged
|
|
|
|
mdccode5150
Full Member
Karma: +12/-4
Offline
Posts: 122
|
|
« Reply #12 on: November 28, 2020, 09:42:30 PM »
|
|
|
I made a pinout for the Hybrids if it'll help anyone. The Saturn might be a dead end pin# 20 doesn't have a wire to pcb.
|
|
|
Logged
|
|
|
|
gremlin
|
|
« Reply #13 on: November 29, 2020, 12:28:00 AM »
|
|
|
No. It will not work with yours above mentioned ECUs.
|
|
|
Logged
|
|
|
|
gremlin
|
|
« Reply #14 on: November 29, 2020, 01:37:15 AM »
|
|
|
The Saturn might be a dead end pin# 20 doesn't have a wire to pcb. ME7.6.x hybrid ECU doesn't have link of MCU boot pin and external connector. This is the difference with similar МЕ7.3.x ECUs. To put MCU in boot mode must find appropriate point(s) on ceramic board. Here is example for ME7.6.2 ECU board for 4-cyl motor. MCU here is ST10F276 with internal flash memory. Your ECU is for 6-cyl motor and use C167 MCU + ext flash chip.
|
|
|
Logged
|
|
|
|
|