Pages: [1]
Author Topic: 066906032AK 0004 golf 4 vr5 2.3  (Read 3319 times)
yutu
Jr. Member
**

Karma: +1/-2
Offline Offline

Posts: 29


« on: February 02, 2023, 11:33:23 AM »

Hi everyone,

I am looking for a2l of 066906032AK. I need ignition timing maps and lambda maps. maybe someone made a chip with a vr5 motor and knows at what addresses these cards are?  here is my original
Logged
Neight
Newbie
*

Karma: +1/-0
Offline Offline

Posts: 9


« Reply #1 on: February 02, 2023, 12:38:05 PM »

Timing start at

011647
01246C

Lambda start

010BAF

Not my cup of tea though. Hope that helps as I am usually of no help. lol
Logged
_nameless
Hero Member
*****

Karma: +324/-450
Offline Offline

Posts: 2708



« Reply #2 on: February 02, 2023, 07:12:05 PM »

Hi everyone,

I am looking for a2l of 066906032AK. I need ignition timing maps and lambda maps. maybe someone made a chip with a vr5 motor and knows at what addresses these cards are?  here is my original

Here I made this file and posted it on another forum, youre more than welcome to use or do whatever with
"I had some time to look into it. After spending the better part of an hour switching between 12v vr6 damos and 30v v6 damos i found enough maps in your file to remove throttle delay, fix lambda request fueling axis values, and make a "stage bro" tune (as I call them). Fueling is 13.0:1 afr at full throttle and max advance of 26-27* UOF and FIL rlvmxn rlvsmxn etc. Crackles and pops on decel and a new custom launch control patch.
Long story short: Crisp, quick throttle response, should feel faster and make all the right noises. Oh yeah and hard cut rev limiter at 6500rpm

One more thing. 2 step has temp check. cars engine coolant needs to be at 75*c or above for 2 step, no lift shift and hard cut rev limit to work. Launch is set at 3500rpm with a locked -2* for launch. No lift shift can be used as a rolling 2 step by keeping the clutch in while full throttle and moving."
« Last Edit: February 10, 2023, 11:19:00 AM by _nameless » Logged

If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/
yutu
Jr. Member
**

Karma: +1/-2
Offline Offline

Posts: 29


« Reply #3 on: February 03, 2023, 03:48:48 PM »

Here I made this file and posted it on another forum, youre more than welcome to use or do whatever with
"I had some time to look into it. After spending the better part of an hour switching between 12v vr6 damos and 30v v6 damos i found enough maps in your file to remove throttle delay, fix lambda request fueling axis values, and make a "stage bro" tune (as I call them). Fueling is 13.0:1 afr at full throttle and max advance of 26-27* UOF and FIL rlvmxn rlvsmxn etc. Crackles and pops on decel and a new custom launch control patch.
Long story short: Crisp, quick throttle response, should feel faster and make all the right noises. Oh yeah and hard cut rev limiter at 6500rpm

One more thing. 2 step has temp check. cars engine coolant needs to be at 75*c or above for 2 step, no lift shift and hard cut rev limit to work. Launch is set at 3500rpm with a locked -2* for launch. No lift shift can be used as a rolling 2 step by keeping the clutch in while full throttle and moving."
But how to make a fuel mixture 1k 16.7 in this firmware? in the range of 1000-2300 rpm and light load? Can you share the damos for this firmware? I want to set up economical operation on gas (propane) fuel in it
Logged
fknbrkn
Hero Member
*****

Karma: +177/-18
Online Online

Posts: 1405


mk4 1.8T AUM


« Reply #4 on: February 10, 2023, 02:31:06 AM »

Here I made this file and posted it on another forum, youre more than welcome to use or do whatever with
"I had some time to look into it. After spending the better part of an hour switching between 12v vr6 damos and 30v v6 damos i found enough maps in your file to remove throttle delay, fix lambda request fueling axis values, and make a "stage bro" tune (as I call them). Fueling is 13.0:1 afr at full throttle and max advance of 26-27* UOF and FIL rlvmxn rlvsmxn etc. Crackles and pops on decel and a new custom launch control patch.
Long story short: Crisp, quick throttle response, should feel faster and make all the right noises. Oh yeah and hard cut rev limiter at 6500rpm

One more thing. 2 step has temp check. cars engine coolant needs to be at 75*c or above for 2 step, no lift shift and hard cut rev limit to work. Launch is set at 3500rpm with a locked -2* for launch. No lift shift can be used as a rolling 2 step by keeping the clutch in while full throttle and moving."

//nvm
« Last Edit: February 10, 2023, 02:55:39 AM by fknbrkn » Logged
yutu
Jr. Member
**

Karma: +1/-2
Offline Offline

Posts: 29


« Reply #5 on: February 10, 2023, 08:33:47 AM »

//nvm

 
did he make a normal tuning firmware? Can I run it?
Logged
fknbrkn
Hero Member
*****

Karma: +177/-18
Online Online

Posts: 1405


mk4 1.8T AUM


« Reply #6 on: February 10, 2023, 10:26:32 AM »

Yep ive got a joke about MRTY BSTRD modules here but take a quick look and thats pretty fine file
Logged
_nameless
Hero Member
*****

Karma: +324/-450
Offline Offline

Posts: 2708



« Reply #7 on: February 10, 2023, 11:22:13 AM »

//nvm

What's the problem?
Logged

If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/
Pages: [1]
  Print  
 
Jump to:  

Powered by SMF 1.1.21 | SMF © 2015, Simple Machines Page created in 0.018 seconds with 17 queries. (Pretty URLs adds 0s, 0q)