lulu2003
Full Member
![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif) ![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif)
Karma: +11/-1
Offline
Posts: 242
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #15 on: April 12, 2012, 07:13:39 AM »
|
|
|
tried nefmoto flasher (OBD) with a ME7.8 but no luck: 04/Apr/2012 10:45:59.609: USER: Validated FTDI device is in dumb mode. 04/Apr/2012 10:45:59.671: LOG: Starting send receive thread. 04/Apr/2012 10:45:59.703: LOG: Send receive thread now started. 04/Apr/2012 10:45:59.703: USER: Disconnected 04/Apr/2012 10:45:59.781: LOG: Setting communication timings to defaults. 04/Apr/2012 10:45:59.781: LOG: Set timing parameters to defaults. 04/Apr/2012 10:45:59.781: USER: Connecting... 04/Apr/2012 10:45:59.812: LOG: Setting communication timings to defaults. 04/Apr/2012 10:45:59.828: USER: Starting slow init connection. 04/Apr/2012 10:46:02.468: USER: Connecting to address 0x01. 04/Apr/2012 10:46:04.703: LOG: Read incorrect sync byte, guessing baud rate is actually 9600. 04/Apr/2012 10:46:04.765: LOG: Not enough key bytes, read: 0 04/Apr/2012 10:46:04.781: USER: Slow init failed. 04/Apr/2012 10:46:04.781: USER: Disconnected 04/Apr/2012 10:46:04.812: LOG: Setting communication timings to defaults. 04/Apr/2012 10:46:04.812: USER: Connecting... 04/Apr/2012 10:46:04.843: LOG: Setting communication timings to defaults. 04/Apr/2012 10:46:04.843: USER: Starting slow init connection. 04/Apr/2012 10:46:07.453: USER: Connecting to address 0x01. 04/Apr/2012 10:46:10.265: LOG: Failed to read sync byte, guessing baud rate is actually 9600. 04/Apr/2012 10:46:10.328: LOG: Not enough key bytes, read: 0 04/Apr/2012 10:46:10.343: USER: Slow init failed. 04/Apr/2012 10:46:10.343: USER: Disconnected 04/Apr/2012 10:46:10.375: LOG: Setting communication timings to defaults. 04/Apr/2012 10:46:10.375: USER: Connecting... 04/Apr/2012 10:46:10.421: LOG: Setting communication timings to defaults. 04/Apr/2012 10:46:10.421: USER: Starting slow init connection. 04/Apr/2012 10:46:13.031: USER: Connecting to address 0x01. 04/Apr/2012 10:46:15.843: LOG: Failed to read sync byte, guessing baud rate is actually 9600. 04/Apr/2012 10:46:15.906: LOG: Not enough key bytes, read: 0 04/Apr/2012 10:46:15.921: USER: Slow init failed. 04/Apr/2012 10:46:15.921: USER: Disconnected 04/Apr/2012 10:46:15.953: LOG: Setting communication timings to defaults. 04/Apr/2012 10:46:15.968: LOG: Closing FTDI device. ME7L succeeds to connect to that ECU but only fails in writing to memory as a limit of the ECU image.
|
|
|
Logged
|
|
|
|
LHN86
Full Member
![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif) ![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif)
Karma: +5/-1
Offline
Posts: 63
Engineer
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #16 on: April 14, 2012, 07:56:59 AM »
|
|
|
I tested the new version no, with orginal ross-tech HEX+CAN. Worked nice to read out in 124800 baud and slow int.
|
|
|
Logged
|
BMW E30 M3 S54
|
|
|
marcellus
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #17 on: April 17, 2012, 05:27:27 PM »
|
|
|
I think my ECU is Screwed now. Please help. I just upgraded to this version of the flasher and in the process of flashing it errored out and now the ecu wont turn on.
17/Apr/2012 04:46:15.400: LOG: Sent message with service ID TransferData 17/Apr/2012 04:46:15.444: LOG: Received message with service ID: TransferDataPositiveResponse 17/Apr/2012 04:46:15.471: LOG: Sent message with service ID TransferData 17/Apr/2012 04:46:15.516: LOG: Received message with service ID: TransferDataPositiveResponse 17/Apr/2012 04:46:15.542: LOG: Sent message with service ID TransferData 17/Apr/2012 04:46:15.586: LOG: Received message with service ID: TransferDataPositiveResponse 17/Apr/2012 04:46:15.612: LOG: Sent message with service ID TransferData 17/Apr/2012 04:46:15.614: LOG: Read incorrect echo from ECU while sending message bytes. Matched first 64 of 65 bytes. 17/Apr/2012 04:46:15.614: LOG: Expected: 00 FB 36 47 BD 93 45 2F B2 B8 45 C0 B5 B9 01 B7 88 B8 9B 89 C3 B3 E5 42 45 89 E2 9D C5 8E 7A B9 E9 93 85 4A 45 9D 9D 43 45 E0 05 89 C3 93 B5 44 45 93 CD 01 05 C0 05 C1 ED 93 85 42 45 9D 9D 4B 45 A8 0B 49 AD 21 BB B7 7A AF B2 44 45 92 C5 4F 04 4F 43 93 45 92 4D 21 BA B7 45 C1 BD B7 09 B8 88 B9 93 87 CB 9C B5 43 4D 9D C5 0E 05 B9 E9 93 85 4A 45 9D 9D 43 45 E0 05 89 C3 B3 C5 44 45 89 C2 9D C5 8E 7A C1 0D CF E5 9C 85 43 4D 93 95 44 45 A9 03 47 A5 2E BB B6 72 A1 BA 4B 45 93 CD 41 0C 40 43 92 4D 9C 45 2E BA B6 4D CF B5 B8 09 B9 80 B7 9B 88 CB 9D BD 4D 45 2E BA B6 4D 9D C5 8E 7A B9 E9 93 85 4A 45 9D 9D 43 45 E0 05 89 C3 93 B5 44 45 93 CD 01 05 C0 05 C1 ED 93 85 42 45 9D 9D 4B 45 A8 0B 49 AD 21 BB B7 7A AF B2 44 45 92 C5 A7 04 4F 43 93 45 92 4D 21 BA B7 45 D1 17/Apr/2012 04:46:15.614: LOG: Read: 00 FB 36 47 BD 93 45 2F B2 B8 45 C0 B5 B9 01 B7 88 B8 9B 89 C3 B3 E5 42 45 89 E2 9D C5 8E 7A B9 E9 93 85 4A 45 9D 9D 43 45 E0 05 89 C3 93 B5 44 45 93 CD 01 05 C0 05 C1 ED 93 85 42 45 9D 9D 4B 00 17/Apr/2012 04:46:15.615: LOG: Clearing remaining expected echo bytes. 17/Apr/2012 04:46:17.619: LOG: Double checking receive buffer for embedded messages before flushing receive buffer due to P1 ECU response inter byte time out. 17/Apr/2012 04:46:17.619: LOG: Flushing 1 bytes from receive buffer due to P1 ECU response inter byte time out. 17/Apr/2012 04:46:17.619: LOG: Message received no replies. 17/Apr/2012 04:46:17.619: LOG: Resending message. Send attempts: 2 17/Apr/2012 04:46:17.643: LOG: Sent message with service ID TransferData 17/Apr/2012 04:46:19.647: LOG: Message received no replies. 17/Apr/2012 04:46:19.647: LOG: Failed to read echo within time limit. Clearing remaining expected echo bytes. 17/Apr/2012 04:46:19.648: LOG: Resending message. Send attempts: 3 17/Apr/2012 04:46:19.673: LOG: Sent message with service ID TransferData 17/Apr/2012 04:46:21.676: LOG: Message received no replies. 17/Apr/2012 04:46:21.676: LOG: Failed to read echo within time limit. Clearing remaining expected echo bytes. 17/Apr/2012 04:46:21.676: LOG: Failed to send message 3 times, message send failed. 17/Apr/2012 04:46:21.677: LOG: Did not receive any replies to message. 17/Apr/2012 04:46:22.175: LOG: Sent message with service ID TesterPresent 17/Apr/2012 04:46:24.177: LOG: Message received no replies. 17/Apr/2012 04:46:24.177: LOG: Failed to read echo within time limit. Clearing remaining expected echo bytes. 17/Apr/2012 04:46:24.177: LOG: Resending message. Send attempts: 2 17/Apr/2012 04:46:24.177: LOG: Sent message with service ID TesterPresent 17/Apr/2012 04:46:26.179: LOG: Message received no replies. 17/Apr/2012 04:46:26.179: LOG: Failed to read echo within time limit. Clearing remaining expected echo bytes. 17/Apr/2012 04:46:26.179: LOG: Resending message. Send attempts: 3 17/Apr/2012 04:46:26.180: LOG: Sent message with service ID TesterPresent 17/Apr/2012 04:46:28.183: LOG: Message received no replies. 17/Apr/2012 04:46:28.183: LOG: Failed to read echo within time limit. Clearing remaining expected echo bytes. 17/Apr/2012 04:46:28.183: LOG: Failed to send message 3 times, message send failed. 17/Apr/2012 04:46:28.183: USER: Disconnecting because no response was received for the Tester Present message. 17/Apr/2012 04:46:28.183: USER: Disconnected 17/Apr/2012 04:46:28.196: LOG: Closing FTDI device. 17/Apr/2012 04:46:28.206: LOG: Send receive thread now terminated. 17/Apr/2012 04:52:18.365: LOG: User Prompt - Title: Communication Error Message: A communication error was encountered while flashing. Press Cancel to abort, or OK to continue after reconnecting. Result: OK 17/Apr/2012 04:52:18.366: USER: Waiting for user to reconnect to ECU before continuing... 17/Apr/2012 04:52:18.367: USER: Waiting for user to reconnect to ECU before continuing... 17/Apr/2012 04:52:26.059: LOG: User Prompt - Title: Confirm Cancel Operation Message: Press OK to cancel the current operation, or Cancel otherwise. Result: OK 17/Apr/2012 04:52:26.059: USER: Cancelling current operation. 17/Apr/2012 04:52:26.069: USER: Writing ECU flash memory failed. 17/Apr/2012 04:52:26.077: USER: 100% complete. 17/Apr/2012 04:52:28.213: USER: Restoring Windows sleep mode. 17/Apr/2012 04:52:34.330: LOG: Closing NefMoto VW Audi ME7 Flasher Logger 1.9.3.0 17/Apr/2012 04:52:38.181: LOG: Opening NefMoto VW Audi ME7 Flasher Logger 1.9.3.0 17/Apr/2012 04:52:38.274: LOG: Cannot load license file, file does not exist: C:\Users\Marcellus\AppData\Roaming\Nefarious Motorsports\NefMoto VW Audi ME7 Flasher Logger\ImportedLicenses.License.dat 17/Apr/2012 04:52:38.321: LOG: Opened NefMoto VW Audi ME7 Flasher Logger 1.9.3.0 17/Apr/2012 04:53:50.362: LOG: Closing NefMoto VW Audi ME7 Flasher Logger 1.9.3.0 17/Apr/2012 04:53:58.198: LOG: Opening NefMoto VW Audi ME7 Flasher Logger 1.9.3.0 17/Apr/2012 04:53:58.268: LOG: Cannot load license file, file does not exist: C:\Users\Marcellus\AppData\Roaming\Nefarious Motorsports\NefMoto VW Audi ME7 Flasher Logger\ImportedLicenses.License.dat 17/Apr/2012 04:53:58.308: LOG: Opened NefMoto VW Audi ME7 Flasher Logger 1.9.3.0 17/Apr/2012 04:54:05.432: LOG: Closing NefMoto VW Audi ME7 Flasher Logger 1.9.3.0 17/Apr/2012 04:55:31.450: LOG: Opening NefMoto VW Audi ME7 Flasher Logger 1.9.3.0 17/Apr/2012 04:55:31.540: LOG: Cannot load license file, file does not exist: C:\Users\Marcellus\AppData\Roaming\Nefarious Motorsports\NefMoto VW Audi ME7 Flasher Logger\ImportedLicenses.License.dat 17/Apr/2012 04:55:31.590: LOG: Opened NefMoto VW Audi ME7 Flasher Logger 1.9.3.0
|
|
|
Logged
|
|
|
|
marcellus
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #18 on: April 18, 2012, 12:39:37 PM »
|
|
|
I tried Minimot (the absolute worst thing to set up for someone like me) and the EEPROM writer in bootmode. Nothing worked. I unplugged the battery over night, and was able to connect and flash with the older Version of the Flasher. I dont know what happenned. Only thing different between this time and all the other times I have been flashing was the Utility itself.
|
|
|
Logged
|
|
|
|
TheDSI
Full Member
![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif) ![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif)
Karma: +12/-0
Offline
Posts: 78
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #19 on: April 22, 2012, 03:23:02 AM »
|
|
|
hi, I've tried to connect to my friends audi S3 AMK with nefmoto ecu flasher with a genuine rosstech hex-usb . when engine is not runing I can connect to ecu with slow init, fast init don't work . 21/avr./2012 05:43:54.984: LOG: Opened FTDI device. 21/avr./2012 05:43:54.984: LOG: FTDI device info - Description: Ross-Tech KII-USB Serial Number: RT000001 Device Type: FT_DEVICE_232R ID: 0x403FA24 Device Flags: 0x0 21/avr./2012 05:43:54.984: LOG: FTDI ChipID DLL is loaded, checking chip ID... 21/avr./2012 05:43:55.000: LOG: FTDI device chip ID: 0x40CFB4D9 21/avr./2012 05:43:55.046: USER: Validated FTDI device is in dumb mode. 21/avr./2012 05:43:55.062: LOG: Starting send receive thread. 21/avr./2012 05:43:55.062: LOG: Send receive thread now started. 21/avr./2012 05:43:55.062: USER: Disconnected 21/avr./2012 05:43:55.093: LOG: Setting communication timings to defaults. 21/avr./2012 05:43:55.093: USER: Connecting... 21/avr./2012 05:43:55.125: LOG: Setting communication timings to defaults. 21/avr./2012 05:43:55.140: USER: Starting fast init connection. 21/avr./2012 05:43:55.140: USER: Connecting to address 0x01. 21/avr./2012 05:43:57.921: USER: Fast init sent, sending start communication request. 21/avr./2012 05:43:59.937: LOG: Message received no replies. 21/avr./2012 05:43:59.937: LOG: Failed to send message 1 times, message send failed. 21/avr./2012 05:43:59.937: USER: Start communication request did not receive any response. 21/avr./2012 05:43:59.937: USER: Disconnected 21/avr./2012 05:43:59.968: LOG: Setting communication timings to defaults. 21/avr./2012 05:43:59.984: USER: Connecting... 21/avr./2012 05:44:00.015: LOG: Setting communication timings to defaults. 21/avr./2012 05:44:00.015: USER: Starting fast init connection. 21/avr./2012 05:44:00.015: USER: Connecting to address 0x01. 21/avr./2012 05:44:02.750: USER: Fast init sent, sending start communication request. 21/avr./2012 05:44:04.796: LOG: Message received no replies. 21/avr./2012 05:44:04.796: LOG: Failed to send message 1 times, message send failed. 21/avr./2012 05:44:04.796: USER: Start communication request did not receive any response. 21/avr./2012 05:44:04.796: USER: Disconnected 21/avr./2012 05:44:04.828: LOG: Setting communication timings to defaults. 21/avr./2012 05:44:04.843: USER: Connecting... 21/avr./2012 05:44:04.875: LOG: Setting communication timings to defaults. 21/avr./2012 05:44:04.875: USER: Starting fast init connection. 21/avr./2012 05:44:04.875: USER: Connecting to address 0x01. 21/avr./2012 05:44:07.609: USER: Fast init sent, sending start communication request. 21/avr./2012 05:44:09.625: LOG: Message received no replies. 21/avr./2012 05:44:09.625: LOG: Failed to send message 1 times, message send failed. 21/avr./2012 05:44:09.625: USER: Start communication request did not receive any response. 21/avr./2012 05:44:09.625: USER: Disconnected 21/avr./2012 05:44:09.656: LOG: Setting communication timings to defaults. 21/avr./2012 05:44:09.671: LOG: Closing FTDI device. 21/avr./2012 05:44:09.671: LOG: Send receive thread now terminated. 21/avr./2012 05:44:22.156: LOG: Opened FTDI device. 21/avr./2012 05:44:22.156: LOG: FTDI device info - Description: Ross-Tech KII-USB Serial Number: RT000001 Device Type: FT_DEVICE_232R ID: 0x403FA24 Device Flags: 0x0 21/avr./2012 05:44:22.156: LOG: FTDI ChipID DLL is loaded, checking chip ID... 21/avr./2012 05:44:22.156: LOG: FTDI device chip ID: 0x40CFB4D9 21/avr./2012 05:44:22.203: USER: Validated FTDI device is in dumb mode. 21/avr./2012 05:44:22.218: LOG: Starting send receive thread. 21/avr./2012 05:44:22.218: LOG: Send receive thread now started. 21/avr./2012 05:44:22.218: USER: Disconnected 21/avr./2012 05:44:22.250: LOG: Setting communication timings to defaults. 21/avr./2012 05:44:22.250: USER: Connecting... 21/avr./2012 05:44:22.281: LOG: Setting communication timings to defaults. 21/avr./2012 05:44:22.281: USER: Starting slow init connection. 21/avr./2012 05:44:24.937: USER: Connecting to address 0x01. 21/avr./2012 05:44:27.125: USER: Slow init succeeded. 21/avr./2012 05:44:27.125: LOG: Setting Address: 0x01 KeyByte1: 0x01 KeyByte2: 0x0A 21/avr./2012 05:44:27.125: USER: Switching to KWP1281 session. 21/avr./2012 05:44:27.312: LOG: KWP1281 read block 21/avr./2012 05:44:27.375: LOG: KWP1281 sent block 21/avr./2012 05:44:27.625: LOG: KWP1281 read block 21/avr./2012 05:44:27.687: LOG: KWP1281 sent block 21/avr./2012 05:44:27.765: LOG: KWP1281 read block 21/avr./2012 05:44:27.828: LOG: KWP1281 sent block 21/avr./2012 05:44:27.968: LOG: KWP1281 read block 21/avr./2012 05:44:28.031: LOG: KWP1281 sent block 21/avr./2012 05:44:28.078: LOG: KWP1281 read block 21/avr./2012 05:44:28.140: LOG: KWP1281 sent block 21/avr./2012 05:44:28.140: USER: KWP1281 connect info: ¸N0906018CH 1.8L R4/5VT G 0005 S¬þ 21/avr./2012 05:44:29.640: USER: Connecting to address 0x01. 21/avr./2012 05:44:31.828: USER: Slow init succeeded. 21/avr./2012 05:44:32.000: LOG: KWP1281 read block 21/avr./2012 05:44:32.062: LOG: KWP1281 sent block 21/avr./2012 05:44:32.343: LOG: KWP1281 read block 21/avr./2012 05:44:32.406: LOG: KWP1281 sent block 21/avr./2012 05:44:32.593: LOG: KWP1281 read block 21/avr./2012 05:44:32.671: LOG: KWP1281 sent block 21/avr./2012 05:44:32.796: LOG: KWP1281 read block 21/avr./2012 05:44:32.859: LOG: KWP1281 sent block 21/avr./2012 05:44:32.906: LOG: KWP1281 read block 21/avr./2012 05:44:32.968: LOG: KWP1281 sent block 21/avr./2012 05:44:32.968: USER: KWP1281 connect info: ¸N0906018CH 1.8L R4/5VT G 0005 S¬þ 21/avr./2012 05:44:34.468: USER: Connecting to address 0x11. 21/avr./2012 05:44:37.281: LOG: Failed to read sync byte, guessing baud rate is actually 9600. 21/avr./2012 05:44:37.343: LOG: Not enough key bytes, read: 0 21/avr./2012 05:44:37.359: USER: Slow init failed. 21/avr./2012 05:44:37.359: USER: Disconnected 21/avr./2012 05:44:37.390: LOG: Setting communication timings to defaults. 21/avr./2012 05:44:37.390: USER: Connecting... 21/avr./2012 05:44:37.421: LOG: Setting communication timings to defaults. 21/avr./2012 05:44:37.437: USER: Starting slow init connection. 21/avr./2012 05:44:40.046: USER: Connecting to address 0x01. 21/avr./2012 05:44:42.218: USER: Slow init succeeded. 21/avr./2012 05:44:42.406: LOG: KWP1281 read block 21/avr./2012 05:44:42.468: LOG: KWP1281 sent block 21/avr./2012 05:44:42.812: LOG: KWP1281 read block 21/avr./2012 05:44:42.875: LOG: KWP1281 sent block 21/avr./2012 05:44:43.046: LOG: KWP1281 read block 21/avr./2012 05:44:43.109: LOG: KWP1281 sent block 21/avr./2012 05:44:43.265: LOG: KWP1281 read block 21/avr./2012 05:44:43.328: LOG: KWP1281 sent block 21/avr./2012 05:44:43.359: LOG: KWP1281 read block 21/avr./2012 05:44:43.421: LOG: KWP1281 sent block 21/avr./2012 05:44:43.421: USER: KWP1281 connect info: ¸N0906018CH 1.8L R4/5VT G 0005 S¬þ 21/avr./2012 05:44:44.921: USER: Connecting to address 0x01. 21/avr./2012 05:44:46.734: LOG: Read incorrect sync byte, guessing baud rate is actually 9600. 21/avr./2012 05:44:46.812: LOG: Not enough key bytes, read: 0 21/avr./2012 05:44:46.828: USER: Slow init failed. 21/avr./2012 05:44:46.828: USER: Disconnected 21/avr./2012 05:44:46.843: LOG: Setting communication timings to defaults. 21/avr./2012 05:44:46.843: USER: Connecting... 21/avr./2012 05:44:46.875: LOG: Setting communication timings to defaults. 21/avr./2012 05:44:46.875: USER: Starting slow init connection. 21/avr./2012 05:44:49.484: USER: Connecting to address 0x01. 21/avr./2012 05:44:51.671: USER: Slow init succeeded. 21/avr./2012 05:44:51.875: LOG: KWP1281 read block 21/avr./2012 05:44:51.937: LOG: KWP1281 sent block 21/avr./2012 05:44:52.171: LOG: KWP1281 read block 21/avr./2012 05:44:52.250: LOG: KWP1281 sent block 21/avr./2012 05:44:52.421: LOG: KWP1281 read block 21/avr./2012 05:44:52.484: LOG: KWP1281 sent block 21/avr./2012 05:44:52.625: LOG: KWP1281 read block 21/avr./2012 05:44:52.687: LOG: KWP1281 sent block 21/avr./2012 05:44:52.734: LOG: KWP1281 read block 21/avr./2012 05:44:52.796: LOG: KWP1281 sent block 21/avr./2012 05:44:52.796: USER: KWP1281 connect info: ¸N0906018CH 1.8L R4/5VT G 0005 S¬þ 21/avr./2012 05:44:54.312: USER: Connecting to address 0x01. 21/avr./2012 05:44:56.500: USER: Slow init succeeded. 21/avr./2012 05:44:56.687: LOG: KWP1281 read block 21/avr./2012 05:44:56.750: LOG: KWP1281 sent block 21/avr./2012 05:44:57.015: LOG: KWP1281 read block 21/avr./2012 05:44:57.078: LOG: KWP1281 sent block 21/avr./2012 05:44:57.265: LOG: KWP1281 read block 21/avr./2012 05:44:57.328: LOG: KWP1281 sent block 21/avr./2012 05:44:57.468: LOG: KWP1281 read block 21/avr./2012 05:44:57.546: LOG: KWP1281 sent block 21/avr./2012 05:44:57.578: LOG: KWP1281 read block 21/avr./2012 05:44:57.640: LOG: KWP1281 sent block 21/avr./2012 05:44:57.640: USER: KWP1281 connect info: ¸N0906018CH 1.8L R4/5VT G 0005 S¬þ 21/avr./2012 05:44:59.171: USER: Connecting to address 0x11. 21/avr./2012 05:45:01.015: LOG: Read incorrect sync byte, guessing baud rate is actually 9600. 21/avr./2012 05:45:01.093: LOG: Not enough key bytes, read: 0 21/avr./2012 05:45:01.093: USER: Slow init failed. 21/avr./2012 05:45:01.093: USER: Disconnected 21/avr./2012 05:45:01.125: LOG: Setting communication timings to defaults. 21/avr./2012 05:45:01.140: LOG: Closing FTDI device. 21/avr./2012 05:45:01.140: LOG: Send receive thread now terminated.
|
|
|
Logged
|
|
|
|
TheDSI
Full Member
![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif) ![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif)
Karma: +12/-0
Offline
Posts: 78
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #20 on: April 22, 2012, 03:23:58 AM »
|
|
|
when I try to start variable reading 21/avr./2012 05:48:46.187: USER: Starting variable reading. 21/avr./2012 05:48:46.203: LOG: Received message with service ID: TesterPresentPositiveReponse 21/avr./2012 05:48:46.531: LOG: Starting DevelopmentSession diagnostic session with 124800 baud rate. 21/avr./2012 05:48:46.531: USER: Starting diagnostic session. 21/avr./2012 05:48:46.562: LOG: Sent message with service ID StartDiagnosticSession 21/avr./2012 05:48:46.609: LOG: Received message with service ID: StartDiagnosticSessionPositiveResponse 21/avr./2012 05:48:46.609: LOG: Setting communication timings to defaults. 21/avr./2012 05:48:46.609: LOG: Changed diagnostic session type to: DevelopmentSession 21/avr./2012 05:48:46.609: LOG: ECU requesting specific baud rate: 124800 21/avr./2012 05:48:46.609: USER: Successfully started diagnostic session. 21/avr./2012 05:48:46.609: USER: Negotiating communication timings. 21/avr./2012 05:48:46.625: LOG: Reading current communication timings. 21/avr./2012 05:48:46.656: LOG: Sent message with service ID AccessTimingParameters 21/avr./2012 05:48:46.671: LOG: Read incorrect echo from ECU while sending message bytes. Matched first 0 of 4 bytes. 21/avr./2012 05:48:46.671: LOG: Expected: 02 83 02 87 21/avr./2012 05:48:46.671: LOG: Read: 00 02 00 06 21/avr./2012 05:48:46.671: LOG: Clearing remaining expected echo bytes. 21/avr./2012 05:48:46.687: LOG: Could not construct valid message from received data: InvalidChecksum 21/avr./2012 05:48:46.687: LOG: Removing first byte from the receive buffer to try to create a valid message. Removed: 0x00 21/avr./2012 05:48:46.687: LOG: Could not construct valid message from received data: InvalidChecksum 21/avr./2012 05:50:30.453: LOG: Removing first byte from the receive buffer to try to create a valid message. Removed: 0x06 21/avr./2012 05:50:32.484: LOG: Double checking receive buffer for embedded messages before flushing receive buffer due to P1 ECU response inter byte time out. 21/avr./2012 05:50:32.484: LOG: Flushing 7 bytes from receive buffer due to P1 ECU response inter byte time out. 21/avr./2012 05:50:32.484: LOG: Message received no replies. 21/avr./2012 05:50:32.484: LOG: Resending message. Send attempts: 2 21/avr./2012 05:50:32.500: LOG: Sent message with service ID AccessTimingParameters 21/avr./2012 05:50:32.500: LOG: Read incorrect echo from ECU while sending message bytes. Matched first 0 of 4 bytes. 21/avr./2012 05:50:32.500: LOG: Expected: 02 83 02 87 21/avr./2012 05:50:32.500: LOG: Read: 00 02 00 06 21/avr./2012 05:50:32.500: LOG: Clearing remaining expected echo bytes. 21/avr./2012 05:50:34.515: LOG: Double checking receive buffer for embedded messages before flushing receive buffer due to P1 ECU response inter byte time out. 21/avr./2012 05:50:34.515: LOG: Flushing 4 bytes from receive buffer due to P1 ECU response inter byte time out. 21/avr./2012 05:50:34.515: LOG: Message received no replies. 21/avr./2012 05:50:34.515: LOG: Resending message. Send attempts: 3 21/avr./2012 05:50:34.531: LOG: Sent message with service ID AccessTimingParameters 21/avr./2012 05:50:34.531: LOG: Read incorrect echo from ECU while sending message bytes. Matched first 0 of 4 bytes. 21/avr./2012 05:50:34.531: LOG: Expected: 02 83 02 87 21/avr./2012 05:50:34.531: LOG: Read: 00 02 00 06 21/avr./2012 05:50:34.531: LOG: Clearing remaining expected echo bytes. 21/avr./2012 05:50:36.531: LOG: Double checking receive buffer for embedded messages before flushing receive buffer due to P1 ECU response inter byte time out. 21/avr./2012 05:50:36.531: LOG: Flushing 4 bytes from receive buffer due to P1 ECU response inter byte time out. 21/avr./2012 05:50:36.531: LOG: Message received no replies. 21/avr./2012 05:50:36.531: LOG: Failed to send message 3 times, message send failed. 21/avr./2012 05:50:36.531: LOG: Did not receive any replies to message. 21/avr./2012 05:50:36.546: USER: 100% complete. 21/avr./2012 05:50:36.546: USER: Stopped reading variables. 21/avr./2012 05:50:36.546: USER: Restoring Windows sleep mode. 21/avr./2012 05:50:37.046: LOG: Sent message with service ID TesterPresent 21/avr./2012 05:50:37.046: LOG: Read incorrect echo from ECU while sending message bytes. Matched first 0 of 4 bytes. 21/avr./2012 05:50:37.046: LOG: Expected: 02 3E 01 41 21/avr./2012 05:50:37.046: LOG: Read: 00 3C 00 00 21/avr./2012 05:50:37.046: LOG: Clearing remaining expected echo bytes. 21/avr./2012 05:50:39.062: LOG: Double checking receive buffer for embedded messages before flushing receive buffer due to P1 ECU response inter byte time out. 21/avr./2012 05:50:39.062: LOG: Flushing 4 bytes from receive buffer due to P1 ECU response inter byte time out. 21/avr./2012 05:50:39.062: LOG: Message received no replies. 21/avr./2012 05:50:39.062: LOG: Resending message. Send attempts: 2 21/avr./2012 05:50:39.078: LOG: Sent message with service ID TesterPresent 21/avr./2012 05:50:39.078: LOG: Read incorrect echo from ECU while sending message bytes. Matched first 0 of 4 bytes. 21/avr./2012 05:50:39.078: LOG: Expected: 02 3E 01 41 21/avr./2012 05:50:39.078: LOG: Read: 00 3C 00 00 21/avr./2012 05:50:39.078: LOG: Clearing remaining expected echo bytes. 21/avr./2012 05:50:41.078: LOG: Double checking receive buffer for embedded messages before flushing receive buffer due to P1 ECU response inter byte time out. 21/avr./2012 05:50:41.078: LOG: Flushing 4 bytes from receive buffer due to P1 ECU response inter byte time out. 21/avr./2012 05:50:41.078: LOG: Message received no replies. 21/avr./2012 05:50:41.078: LOG: Resending message. Send attempts: 3 21/avr./2012 05:50:41.109: LOG: Sent message with service ID TesterPresent 21/avr./2012 05:50:41.109: LOG: Read incorrect echo from ECU while sending message bytes. Matched first 0 of 4 bytes. 21/avr./2012 05:50:41.109: LOG: Expected: 02 3E 01 41 21/avr./2012 05:50:41.109: LOG: Read: 00 3C 00 00 21/avr./2012 05:50:41.109: LOG: Clearing remaining expected echo bytes. 21/avr./2012 05:50:43.109: LOG: Double checking receive buffer for embedded messages before flushing receive buffer due to P1 ECU response inter byte time out. 21/avr./2012 05:50:43.109: LOG: Flushing 4 bytes from receive buffer due to P1 ECU response inter byte time out. 21/avr./2012 05:50:43.109: LOG: Message received no replies. 21/avr./2012 05:50:43.109: LOG: Failed to send message 3 times, message send failed. 21/avr./2012 05:50:43.109: USER: Disconnecting because no response was received for the Tester Present message. 21/avr./2012 05:50:43.109: USER: Disconnected 21/avr./2012 05:50:43.171: LOG: Closing FTDI device. 21/avr./2012 05:50:43.171: LOG: Send receive thread now terminated.
|
|
« Last Edit: April 22, 2012, 03:26:55 AM by TheDSI »
|
Logged
|
|
|
|
TheDSI
Full Member
![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif) ![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif)
Karma: +12/-0
Offline
Posts: 78
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #21 on: April 22, 2012, 03:27:56 AM »
|
|
|
when I try to connect slow init when engine is running 21/avr./2012 05:42:47.984: LOG: Opened NefMoto VW Audi ME7 Flasher Logger 1.9.3.0 21/avr./2012 05:43:00.500: LOG: Setting Address: 0x01 KeyByte1: 0x6B KeyByte2: 0x0F 21/avr./2012 05:43:00.578: LOG: Opened FTDI device. 21/avr./2012 05:43:00.578: LOG: FTDI device info - Description: Ross-Tech KII-USB Serial Number: RT000001 Device Type: FT_DEVICE_232R ID: 0x403FA24 Device Flags: 0x0 21/avr./2012 05:43:00.578: LOG: FTDI ChipID DLL is loaded, checking chip ID... 21/avr./2012 05:43:00.593: LOG: FTDI device chip ID: 0x40CFB4D9 21/avr./2012 05:43:00.671: USER: Validated FTDI device is in dumb mode. 21/avr./2012 05:43:00.687: LOG: Starting send receive thread. 21/avr./2012 05:43:00.687: LOG: Send receive thread now started. 21/avr./2012 05:43:00.734: USER: Disconnected 21/avr./2012 05:43:00.750: LOG: Setting communication timings to defaults. 21/avr./2012 05:43:00.750: LOG: Set timing parameters to defaults. 21/avr./2012 05:43:00.750: USER: Connecting... 21/avr./2012 05:43:00.765: LOG: Setting communication timings to defaults. 21/avr./2012 05:43:00.781: USER: Starting slow init connection. 21/avr./2012 05:43:03.390: USER: Connecting to address 0x01. 21/avr./2012 05:43:05.593: USER: Slow init succeeded. 21/avr./2012 05:43:05.593: LOG: Setting Address: 0x01 KeyByte1: 0x01 KeyByte2: 0x0A 21/avr./2012 05:43:05.593: USER: Switching to KWP1281 session. 21/avr./2012 05:43:05.781: LOG: KWP1281 read block 21/avr./2012 05:43:05.843: LOG: KWP1281 sent block 21/avr./2012 05:43:06.187: LOG: KWP1281 read block 21/avr./2012 05:43:06.250: LOG: KWP1281 sent block 21/avr./2012 05:43:06.328: LOG: KWP1281 read block 21/avr./2012 05:43:06.390: LOG: KWP1281 sent block 21/avr./2012 05:43:06.531: LOG: KWP1281 read block 21/avr./2012 05:43:06.593: LOG: KWP1281 sent block 21/avr./2012 05:43:06.640: LOG: KWP1281 read block 21/avr./2012 05:43:06.703: LOG: KWP1281 sent block 21/avr./2012 05:43:06.703: USER: KWP1281 connect info: ¸N0906018CH 1.8L R4/5VT G 0005 S¬þ 21/avr./2012 05:43:08.203: USER: Connecting to address 0x01. 21/avr./2012 05:43:10.390: USER: Slow init succeeded. 21/avr./2012 05:43:10.578: LOG: KWP1281 read block 21/avr./2012 05:43:10.640: LOG: KWP1281 sent block 21/avr./2012 05:43:10.906: LOG: KWP1281 read block 21/avr./2012 05:43:10.968: LOG: KWP1281 sent block 21/avr./2012 05:43:11.156: LOG: KWP1281 read block 21/avr./2012 05:43:11.218: LOG: KWP1281 sent block 21/avr./2012 05:43:11.359: LOG: KWP1281 read block 21/avr./2012 05:43:11.421: LOG: KWP1281 sent block 21/avr./2012 05:43:11.453: LOG: KWP1281 read block 21/avr./2012 05:43:11.531: LOG: KWP1281 sent block 21/avr./2012 05:43:11.531: USER: KWP1281 connect info: ¸N0906018CH 1.8L R4/5VT G 0005 S¬þ 21/avr./2012 05:43:13.031: USER: Connecting to address 0x11. 21/avr./2012 05:43:15.843: LOG: Failed to read sync byte, guessing baud rate is actually 9600. 21/avr./2012 05:43:15.906: LOG: Not enough key bytes, read: 0 21/avr./2012 05:43:15.921: USER: Slow init failed. 21/avr./2012 05:43:15.921: USER: Disconnected 21/avr./2012 05:43:15.937: LOG: Setting communication timings to defaults. 21/avr./2012 05:43:15.937: USER: Connecting... 21/avr./2012 05:43:15.968: LOG: Setting communication timings to defaults. 21/avr./2012 05:43:15.968: USER: Starting slow init connection. 21/avr./2012 05:43:18.578: USER: Connecting to address 0x01. 21/avr./2012 05:43:20.781: USER: Slow init succeeded. 21/avr./2012 05:43:20.968: LOG: KWP1281 read block 21/avr./2012 05:43:21.031: LOG: KWP1281 sent block 21/avr./2012 05:43:21.281: LOG: KWP1281 read block 21/avr./2012 05:43:21.343: LOG: KWP1281 sent block 21/avr./2012 05:43:21.531: LOG: KWP1281 read block 21/avr./2012 05:43:21.593: LOG: KWP1281 sent block 21/avr./2012 05:43:21.734: LOG: KWP1281 read block 21/avr./2012 05:43:21.796: LOG: KWP1281 sent block 21/avr./2012 05:43:21.843: LOG: KWP1281 read block 21/avr./2012 05:43:21.906: LOG: KWP1281 sent block 21/avr./2012 05:43:21.906: USER: KWP1281 connect info: ¸N0906018CH 1.8L R4/5VT G 0005 S¬þ 21/avr./2012 05:43:23.406: USER: Connecting to address 0x01. 21/avr./2012 05:43:25.593: USER: Slow init succeeded. 21/avr./2012 05:43:25.781: LOG: KWP1281 read block 21/avr./2012 05:43:25.843: LOG: KWP1281 sent block 21/avr./2012 05:43:26.109: LOG: KWP1281 read block 21/avr./2012 05:43:26.171: LOG: KWP1281 sent block 21/avr./2012 05:43:26.359: LOG: KWP1281 read block 21/avr./2012 05:43:26.421: LOG: KWP1281 sent block 21/avr./2012 05:43:26.578: LOG: KWP1281 read block 21/avr./2012 05:43:26.640: LOG: KWP1281 sent block 21/avr./2012 05:43:26.671: LOG: KWP1281 read block 21/avr./2012 05:43:26.734: LOG: KWP1281 sent block 21/avr./2012 05:43:26.734: USER: KWP1281 connect info: ¸N0906018CH 1.8L R4/5VT G 0005 S¬þ 21/avr./2012 05:43:28.234: USER: Connecting to address 0x11. 21/avr./2012 05:43:31.046: LOG: Failed to read sync byte, guessing baud rate is actually 9600. 21/avr./2012 05:43:31.109: LOG: Not enough key bytes, read: 0 21/avr./2012 05:43:31.125: USER: Slow init failed. 21/avr./2012 05:43:31.125: USER: Disconnected 21/avr./2012 05:43:31.156: LOG: Setting communication timings to defaults. 21/avr./2012 05:43:31.156: USER: Connecting... 21/avr./2012 05:43:31.171: LOG: Setting communication timings to defaults. 21/avr./2012 05:43:31.171: USER: Starting slow init connection. 21/avr./2012 05:43:33.781: USER: Connecting to address 0x01. 21/avr./2012 05:43:35.968: USER: Slow init succeeded. 21/avr./2012 05:43:36.156: LOG: KWP1281 read block 21/avr./2012 05:43:36.218: LOG: KWP1281 sent block 21/avr./2012 05:43:36.484: LOG: KWP1281 read block 21/avr./2012 05:43:36.546: LOG: KWP1281 sent block 21/avr./2012 05:43:36.718: LOG: KWP1281 read block 21/avr./2012 05:43:36.781: LOG: KWP1281 sent block 21/avr./2012 05:43:36.921: LOG: KWP1281 read block 21/avr./2012 05:43:36.984: LOG: KWP1281 sent block 21/avr./2012 05:43:37.031: LOG: KWP1281 read block 21/avr./2012 05:43:37.093: LOG: KWP1281 sent block 21/avr./2012 05:43:37.093: USER: KWP1281 connect info: ¸N0906018CH 1.8L R4/5VT G 0005 S¬þ 21/avr./2012 05:43:38.609: USER: Connecting to address 0x01. 21/avr./2012 05:43:40.859: USER: Slow init succeeded. 21/avr./2012 05:43:41.031: LOG: KWP1281 read block 21/avr./2012 05:43:41.093: LOG: KWP1281 sent block 21/avr./2012 05:43:41.375: LOG: KWP1281 read block 21/avr./2012 05:43:41.437: LOG: KWP1281 sent block 21/avr./2012 05:43:41.625: LOG: KWP1281 read block 21/avr./2012 05:43:41.687: LOG: KWP1281 sent block 21/avr./2012 05:43:41.843: LOG: KWP1281 read block 21/avr./2012 05:43:41.906: LOG: KWP1281 sent block 21/avr./2012 05:43:41.953: LOG: KWP1281 read block 21/avr./2012 05:43:42.015: LOG: KWP1281 sent block 21/avr./2012 05:43:42.015: USER: KWP1281 connect info: ¸N0906018CH 1.8L R4/5VT G 0005 S¬þ 21/avr./2012 05:43:43.515: USER: Connecting to address 0x11. 21/avr./2012 05:43:46.328: LOG: Failed to read sync byte, guessing baud rate is actually 9600. 21/avr./2012 05:43:46.390: LOG: Not enough key bytes, read: 0 21/avr./2012 05:43:46.406: USER: Slow init failed. 21/avr./2012 05:43:46.406: USER: Disconnected 21/avr./2012 05:43:46.421: LOG: Setting communication timings to defaults. 21/avr./2012 05:43:46.453: LOG: Closing FTDI device. 21/avr./2012 05:43:46.453: LOG: Send receive thread now terminated.
|
|
« Last Edit: April 22, 2012, 03:31:37 AM by TheDSI »
|
Logged
|
|
|
|
nyet
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #22 on: May 07, 2012, 11:45:19 AM »
|
|
|
I'm having problems with in car flash.
I get a security error. I'll post logs next time i try flashing.
currently, i HAVE to use the bench flasher.
|
|
|
Logged
|
|
|
|
Snow Trooper
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #23 on: May 07, 2012, 05:13:15 PM »
|
|
|
I'm having problems with in car flash.
I get a security error. I'll post logs next time i try flashing.
currently, i HAVE to use the bench flasher.
That happened to me after a recent Vcds update, I reinstalled nef, drivers and deleted all old Rosstech drivers and issue went away.
|
|
|
Logged
|
cartoons? 6A 61 72 65 64 40 76 6C 6D 73 70 65 63
|
|
|
nyet
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #24 on: May 07, 2012, 05:20:42 PM »
|
|
|
Thanks ST, i'll give that a shot tonight.
|
|
|
Logged
|
|
|
|
nyet
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #25 on: May 08, 2012, 01:16:00 PM »
|
|
|
no joy 08/May/2012 01:10:27.947: USER: Requesting security access. 08/May/2012 01:10:27.974: LOG: Sent message with service ID SecurityAccess 08/May/2012 01:10:28.020: LOG: Received message with service ID: NegativeResponse 08/May/2012 01:10:28.023: LOG: Received negative response for service ID: SecurityAccess, with response code: GeneralReject 08/May/2012 01:10:28.027: USER: ECU reports that security access request was rejected. 08/May/2012 01:10:07.880: LOG: Opened FTDI device. 08/May/2012 01:10:07.881: LOG: FTDI device info - Description: FT232R USB UART Serial Number: A400GNA4 Device Type: FT_DEVICE_232R ID: 0x4036001 Device Flags: 0x0 08/May/2012 01:10:07.882: LOG: FTDI ChipID DLL is loaded, checking chip ID... 08/May/2012 01:10:07.883: LOG: FTDI device chip ID: 0xEC7BA6D5 08/May/2012 01:10:07.893: USER: Validated FTDI device is in dumb mode. 08/May/2012 01:10:07.898: LOG: Starting send receive thread. 08/May/2012 01:10:07.900: LOG: Send receive thread now started. 08/May/2012 01:10:07.900: USER: Disconnected 08/May/2012 01:10:07.915: LOG: Setting communication timings to defaults. 08/May/2012 01:10:07.915: USER: Connecting... 08/May/2012 01:10:07.932: LOG: Setting communication timings to defaults. 08/May/2012 01:10:07.933: USER: Starting slow init connection. 08/May/2012 01:10:10.533: USER: Connecting to address 0x01. 08/May/2012 01:10:12.679: USER: Slow init succeeded. 08/May/2012 01:10:12.680: LOG: Setting Address: 0x01 KeyByte1: 0x01 KeyByte2: 0x0A 08/May/2012 01:10:12.680: USER: Switching to KWP1281 session. 08/May/2012 01:10:12.861: LOG: KWP1281 read block 08/May/2012 01:10:12.925: LOG: KWP1281 sent block 08/May/2012 01:10:13.193: LOG: KWP1281 read block 08/May/2012 01:10:13.257: LOG: KWP1281 sent block 08/May/2012 01:10:13.435: LOG: KWP1281 read block 08/May/2012 01:10:13.499: LOG: KWP1281 sent block 08/May/2012 01:10:13.645: LOG: KWP1281 read block 08/May/2012 01:10:13.708: LOG: KWP1281 sent block 08/May/2012 01:10:13.746: LOG: KWP1281 read block 08/May/2012 01:10:13.810: LOG: KWP1281 sent block 08/May/2012 01:10:13.811: USER: KWP1281 connect info: 8D0907551M 2.7l V6/5VT G 0002 4oTO 08/May/2012 01:10:15.311: USER: Connecting to address 0x01. 08/May/2012 01:10:17.486: USER: Slow init succeeded. 08/May/2012 01:10:17.487: LOG: Setting Address: 0x01 KeyByte1: 0x6F KeyByte2: 0x0F 08/May/2012 01:10:17.488: USER: Switching to KWP2000 session. 08/May/2012 01:10:17.488: USER: Connected 08/May/2012 01:10:20.037: LOG: Sent message with service ID TesterPresent 08/May/2012 01:10:20.073: LOG: Received message with service ID: TesterPresentPositiveReponse 08/May/2012 01:10:22.554: LOG: Sent message with service ID TesterPresent 08/May/2012 01:10:22.598: LOG: Received message with service ID: TesterPresentPositiveReponse 08/May/2012 01:10:25.072: LOG: Sent message with service ID TesterPresent 08/May/2012 01:10:25.111: LOG: Received message with service ID: TesterPresentPositiveReponse 08/May/2012 01:10:27.499: USER: Disabling Windows sleep mode. 08/May/2012 01:10:27.549: USER: Writing ECU flash memory. 08/May/2012 01:10:27.591: LOG: Sent message with service ID TesterPresent 08/May/2012 01:10:27.593: LOG: Reading ECU identification option: 0x9C 08/May/2012 01:10:27.625: LOG: Received message with service ID: TesterPresentPositiveReponse 08/May/2012 01:10:27.663: LOG: Sent message with service ID ReadECUIdentification 08/May/2012 01:10:27.711: LOG: Received message with service ID: ReadECUIdentificationPositiveResponse 08/May/2012 01:10:27.716: LOG: Read ECU identification option: 0x9C 08/May/2012 01:10:27.716: LOG: Successfully read ECU identification information 08/May/2012 01:10:27.736: USER: ECU reports programming session preconditions have been met. 08/May/2012 01:10:27.740: USER: Negotiating communication timings. 08/May/2012 01:10:27.740: LOG: Reading current communication timings. 08/May/2012 01:10:27.757: LOG: Sent message with service ID AccessTimingParameters 08/May/2012 01:10:27.803: LOG: Received message with service ID: AccessTimingParametersPositiveResponse 08/May/2012 01:10:27.806: LOG: Set timing parameters to new values. 08/May/2012 01:10:27.806: LOG: Setting communication timing to defaults. 08/May/2012 01:10:27.829: LOG: Sent message with service ID AccessTimingParameters 08/May/2012 01:10:27.869: LOG: Received message with service ID: AccessTimingParametersPositiveResponse 08/May/2012 01:10:27.869: LOG: Reading current communication timings. 08/May/2012 01:10:27.901: LOG: Sent message with service ID AccessTimingParameters 08/May/2012 01:10:27.943: LOG: Received message with service ID: AccessTimingParametersPositiveResponse 08/May/2012 01:10:27.944: USER: Successfully changed to new communication timings. 08/May/2012 01:10:27.947: USER: Requesting security access. 08/May/2012 01:10:27.974: LOG: Sent message with service ID SecurityAccess 08/May/2012 01:10:28.020: LOG: Received message with service ID: NegativeResponse 08/May/2012 01:10:28.023: LOG: Received negative response for service ID: SecurityAccess, with response code: GeneralReject 08/May/2012 01:10:28.027: USER: ECU reports that security access request was rejected. 08/May/2012 01:10:28.031: LOG: Starting ProgrammingSession diagnostic session with 124800 baud rate. 08/May/2012 01:10:28.032: USER: Starting diagnostic session. 08/May/2012 01:10:28.054: LOG: Sent message with service ID StartDiagnosticSession 08/May/2012 01:10:28.090: LOG: Received message with service ID: NegativeResponse 08/May/2012 01:10:28.091: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending 08/May/2012 01:10:28.130: LOG: Received message with service ID: NegativeResponse 08/May/2012 01:10:28.131: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending 08/May/2012 01:10:28.170: LOG: Received message with service ID: NegativeResponse 08/May/2012 01:10:28.171: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending 08/May/2012 01:10:28.210: LOG: Received message with service ID: NegativeResponse
|
|
|
Logged
|
|
|
|
nyet
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #26 on: May 08, 2012, 01:39:04 PM »
|
|
|
ah interesting. on the bench i also get the same security error, but it ignores the problem and completes fine 08/May/2012 01:10:28.286: LOG: Received message with service ID: NegativeResponse 08/May/2012 01:10:28.287: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending 08/May/2012 01:10:28.326: LOG: Received message with service ID: NegativeResponse 08/May/2012 01:10:28.327: LOG: Received negative response for service ID: StartDiagnosticSession, with response code: RequestCorrectlyReceived_ResponsePending 08/May/2012 01:10:28.362: LOG: Received message with service ID: StartDiagnosticSessionPositiveResponse 08/May/2012 01:10:28.369: LOG: Setting communication timings to defaults. 08/May/2012 01:10:28.370: LOG: Set timing parameters to defaults.
when in the car, it just goes into a loop with that negative response forever. on the bench it continues as above
|
|
|
Logged
|
|
|
|
nyet
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #27 on: May 08, 2012, 01:41:23 PM »
|
|
|
That happened to me after a recent Vcds update, I reinstalled nef, drivers and deleted all old Rosstech drivers and issue went away.
which drivers did you install? off of ftd site, or whatever win7 automatically installs?
|
|
|
Logged
|
|
|
|
Snow Trooper
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #28 on: May 09, 2012, 10:56:29 AM »
|
|
|
I use Vcds v10.8 and my custom vcp drivers. The new Ross tech drivers don't get along with much of anything it seems
|
|
|
Logged
|
cartoons? 6A 61 72 65 64 40 76 6C 6D 73 70 65 63
|
|
|
Jason
Hero Member
![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif) ![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif) ![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif) ![*](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/star.gif)
Karma: +38/-0
Offline
Posts: 500
Breaks everything!
|
![](http://nefariousmotorsports.com/forum/Themes/nefmoto/images/post/xx.gif) |
« Reply #29 on: May 09, 2012, 10:59:45 AM »
|
|
|
And the installer is rather persistent in trying to trick you into installing them.
|
|
|
Logged
|
|
|
|
|