mRj
Jr. Member
Karma: +0/-0
 Offline
Posts: 35
|
 |
« on: April 25, 2013, 01:17:24 AM »
|
|
|
Hi
My Seat Leon 1.8T AUQ has a remap on, but now i notice that in 4th gear my limiter hits at 6.1k, although my cars rev limiter is set to 7.1k.
Also 5th gear loses all power/boost and wont go again till i take out of gear and put back in. I did think throttle cut, but no errors on ECU.
Can anyone help?
|
|
|
|
|
Logged
|
|
|
|
|
aef
|
|
« Reply #1 on: April 25, 2013, 02:11:09 AM »
|
|
|
Help with?
Post your file or ask the tuner which you payd for this tune.
|
|
|
|
|
Logged
|
|
|
|
mRj
Jr. Member
Karma: +0/-0
Offline
Posts: 35
|
|
« Reply #2 on: April 25, 2013, 03:37:29 AM »
|
|
|
what would cause it, could it be the torque limiters for each gear?
|
|
|
|
|
Logged
|
|
|
|
|
littco
|
|
« Reply #3 on: April 25, 2013, 03:45:06 AM »
|
|
|
what would cause it, could it be the torque limiters for each gear?
There is a gear based torque limit map KFMDBGRG, but it limits kfmiop not rpm. |
|
|
|
|
Logged
|
|
|
|
mRj
Jr. Member
Karma: +0/-0
Offline
Posts: 35
|
|
« Reply #4 on: April 25, 2013, 03:48:22 AM »
|
|
|
ok
also im not sure if this happened since i added in the launch control.
i will test tonight by removing the launch control.
has anyone seen this happen before on a 1.8t?
|
|
|
|
|
Logged
|
|
|
|
CoupedUp
Full Member
Karma: +0/-0
Offline
Posts: 59
|
|
« Reply #5 on: April 25, 2013, 05:47:36 AM »
|
|
|
Could it be a speed limiter instead of rev/torque. Surely not, but just making sure the small things aren't overlooked.
|
|
|
|
|
Logged
|
|
|
|
mRj
Jr. Member
Karma: +0/-0
Offline
Posts: 35
|
|
« Reply #6 on: April 25, 2013, 05:51:38 AM »
|
|
|
Could it be a speed limiter instead of rev/torque. Surely not, but just making sure the small things aren't overlooked.
hi im fairly new to tuning these (know a lot about ms41.0 lol) what is the map name for speedlimiter? |
|
|
|
|
Logged
|
|
|
|
|
phila_dot
|
|
« Reply #7 on: April 25, 2013, 06:11:08 AM »
|
|
|
There is a gear based torque limit map KFMDBGRG, but it limits kfmiop not rpm.
No, it limits spec load via milsol. |
|
|
|
|
Logged
|
|
|
|
|
littco
|
|
« Reply #8 on: April 25, 2013, 07:50:11 AM »
|
|
|
No, it limits spec load via milsol.
Hi I was going on the FR and I dont doubt your knowledge Phil , the table is 0-100 so how can it limit spec load as a %? I have never used I will add but just added it to my mappack after reading FR as i thought it sounded worth testing. KFMDBGRG Kennfeld mit dem Wert der Momentenbegrenzung Map the value of the torque limit |
|
|
|
|
Logged
|
|
|
|
|
phila_dot
|
|
« Reply #9 on: April 25, 2013, 08:02:09 AM »
|
|
|
Look at %MDKOL -> %MDFUE
It limits the input to KFMIRL
|
|
|
|
|
Logged
|
|
|
|
|
littco
|
|
« Reply #10 on: April 25, 2013, 08:12:03 AM »
|
|
|
Look at %MDKOL -> %MDFUE
It limits the input to KFMIRL
I must be missing something or having a bad day. Kfmdbgrg output is mibgr_w I see no mention Mdkol or mdfue What I Missed? |
|
|
|
|
Logged
|
|
|
|
|
phila_dot
|
|
« Reply #11 on: April 25, 2013, 08:23:29 AM »
|
|
|
They are functions
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #12 on: April 25, 2013, 08:25:31 AM »
|
|
|
They are functions
More specifically, the FR is organized by functions. The TOC in the PDF consists of the list of functions. |
|
|
|
|
Logged
|
|
|
|
mRj
Jr. Member
Karma: +0/-0
Offline
Posts: 35
|
|
« Reply #13 on: April 25, 2013, 12:30:01 PM »
|
|
|
all sorted, was the launch control i edited. could it of been DNMAXH (16304) This is the RPM above rev limit when the fuel cut comes on. Tweaking this helps make more boost on the limiter. I use 50 RPM (Keep in mind the maximum RPM limit is NMAXOG + DNMAXH) causing it? |
|
|
|
|
Logged
|
|
|
|
|
littco
|
|
« Reply #14 on: April 26, 2013, 02:09:06 AM »
|
|
|
They are functions
I know they are functions, ipad auto correct, it missed "in" I was trying to say I see no mention of KFMDBGRG in either function and I still don't, let alone showing milsol is the output.. |
|
|
|
|
Logged
|
|
|
|
|
