Audi A4 B5: Help with IMMO PIN from 95040 Read

Pages: [1]

« previous next »

Author

Topic: Audi A4 B5: Help with IMMO PIN from 95040 Read (Read 9695 times)

locutas

Newbie

Karma: +0/-0
Offline

Offline

Posts: 2

	Audi A4 B5: Help with IMMO PIN from 95040 Read « on: August 05, 2016, 08:37:10 AM »

Hello,

I was able to read my immo (Audi A4 B5 ECU 8D0906018E) using Argdub's EEPROM reader. Problem is I can't seem to identify the PIN/SKC from the .bin file. The relevant lines contain FF FF and nothing else. Kindly advise if I'm doing something wrong and assist with extracting the PIN/SKC from the attached file.
Many thanks.


	Logged

macxxx

Sr. Member

Karma: +30/-1
Offline

Offline

Posts: 498

	Re: « Reply #1 on: August 05, 2016, 12:31:14 PM »

Probably Immo2 so there is no pin in ecu

Engine code is ARG?


	Logged

locutas

Newbie

Karma: +0/-0
Offline

Offline

Posts: 2

	Re: « Reply #2 on: August 06, 2016, 12:13:24 PM »

Quote from: macxxx on August 05, 2016, 12:31:14 PM

Probably Immo2 so there is no pin in ecu

Engine code is ARG?

No. Engine is APT.


	Logged

macxxx

Sr. Member

Karma: +30/-1
Offline

Offline

Posts: 498

	Re: « Reply #3 on: August 06, 2016, 10:21:47 PM »

Ok doesn't matter the code Wink

check 17-instruments using vcds/vagcom , if there is only immo id ( AUZ... etc ) a no VIN then it's immo2 for sure.


	Logged

EuroXs4

Full Member

Karma: +15/-31
Offline

Offline

Posts: 209

	Re: Audi A4 B5: Help with IMMO PIN from 95040 Read « Reply #4 on: August 18, 2016, 06:02:22 PM »

Locutas this looks like a virgin dump rather than a read from your ecu. no vin or immo id either.Pin looks to be 0001.But the dump looks to be incomplete.Is this a european ecu??
I


« Last Edit: August 19, 2016, 04:00:27 AM by EuroXs4 »	Logged

macxxx

Sr. Member

Karma: +30/-1
Offline

Offline

Posts: 498

	Re: « Reply #5 on: August 18, 2016, 09:51:06 PM »

It's from ecu


	Logged

Shabangabang

Newbie

Karma: +0/-0
Offline

Offline

Posts: 2

	Re: « Reply #6 on: October 06, 2016, 06:37:30 AM »

Hi guys

I'm posting here because i have a 2000 Audi A4 B5 that I just cannot seem to read the 95040 Bin with Argdubs Tool. Below is the response i'm getting.

I have been able to pull the Instrument Cluster Eprom dump (attached) using the VAG K Comander Lead and software version 1.4 which is 2048k . I have run this through the eeprom tool but the tool has problems parsing the 2k bin file. I have had no luck getting the ECU Eprom Dump usign the VAG K Commander.

All i really want is to get the SKC code from the BIN file so i can replace the only key i lost for my Audi Avant. Like most punters i'm loth to pay the $800 for a key to be sent from Germany to Australia.

Can the SKC code be read from the 2048k Instrument Cluster Bin? If so which blocks do i need to read??

C:\Users\sheldon\Desktop\EpromBoot\argdubsTool>me7_95040.exe --OBD -r -p4 eeprom
.bin
Ver: 1.31
Com Port: 4
Baud Rate: 10400
Opening COM4 ... OK
Initiating communication ... OK
ECU ID response: 3B0907552P
2.4L V6/5V G
0001
SoftCod: 04551, WSC: 20690
Reading EEPROM .................................................................
FAIL. (error=0x01)
Closing COM4


	Logged

macxxx

Sr. Member

Karma: +30/-1
Offline

Offline

Posts: 498

	Re: « Reply #7 on: October 06, 2016, 06:54:21 AM »

The pin must be in the cluster dump...it is 3 times repeated in the end...im writing from tapatalk i can check it later


	Logged

macxxx

Sr. Member

Karma: +30/-1
Offline

Offline

Posts: 498

	Re: « Reply #8 on: October 06, 2016, 01:56:55 PM »

6A1A - swap byte 1A6A - DEC 6762

so your PIN is 6762

You have immo2 so reading Epprom from ecu wouldn't help you...


« Last Edit: October 06, 2016, 01:58:41 PM by macxxx »	Logged

Shabangabang

Newbie

Karma: +0/-0
Offline

Offline

Posts: 2

	Re: Audi A4 B5: Help with IMMO PIN from 95040 Read « Reply #9 on: October 10, 2016, 06:28:24 AM »

Hi Macxx

Thanks for your quick reply on the question of how to establish the SKC from the immobilizer bin file. I saw another post that also confirmed to look for the hex reference repeated 3 times in the immobilizer cluster bin file. I did try the code in VCDS under the "immobilizer section / Login" section but VCDS would not except the code for some reason. I was hoping to confirm the details of the currently configured but lost key in VCDS.

I'm waiting for a immo 2 key fob to come in the mail soon so will try again shortly. I have also purchased the 5.5 Vag K Commander Cable with the hopes of being able to pull the ECU' bin. I cannot work out why i cannot receive the ECU bin after establishing a connection.


	Logged

macxxx

Sr. Member

Karma: +30/-1
Offline

Offline

Posts: 498

	Re: « Reply #10 on: October 10, 2016, 08:13:15 AM »

Try to change the latency time in Windows setting of com port to 1ms


	Logged

Pages: [1]

« previous next »

Jump to:

Navigation

Personal Tools

May 08, 2024, 11:59:51 PM

Welcome, Guest. Please login or register.
Did you miss your activation email?

Navigation

Personal Tools

Search