richo_vw
Newbie
Karma: +0/-0
 Offline
Posts: 6
|
 |
« on: April 11, 2020, 01:38:43 PM »
|
|
|
Hi to all,
I've been reading the forum for a while (i´m still a newie), and thanks to the quarantine I now have some time to start messing around with an ecu and a couple of dashboards that I had as a replacement for my audi TT.
Time ago I bought an Me7.5 8n0906018F-0261206105 with its dashboard 8N1 919880E and its key, all from the same donor.
These days I have made a bench to work with it. The bench consist on the dashboard with the rfid coil, the ecu and a OBD port.
It works well, when I power the bench the dashboard recognize the rfid chip and the immo light turn off, If i power up the bench without the key in the rfid coil the immo light on the dashboard keeps flashing as it should
I can read the 95040 in bootmode without problems and I can write it too, But if I write a immo off .bin it doesn´t work. I tried modifying the original one, with the eeprom tool, manually and with a virgin one but nothing of this worked.
If i try to read the flash with nefmoto it connects to the ecu but says: “Validation Falied. ECU reports RequestUpload service is not supported. Request upload may have been disabled by aftermarket engine software”, different baud rates neither work
This message in addition with the eeprom problem makes me think that the ecu has a previous tune
¿What do you think? ¿what should be my next steps, flash an ori file and a virgin 95040?
I attach the original .bin from the eeprom, and two immo off files I tried and doesn’t work
Me7.5 8N0906018F -0261206105 SW:1037350745
Not sure if this should be posted here, Thanks
|
|
|
|
|
Logged
|
patience please!!! newie ahead
|
|
|
|
BlackT
|
|
« Reply #1 on: April 11, 2020, 02:07:37 PM »
|
|
|
Upload your flash or send me to my PM I will compare it with ori, you can read it by galleto in boot mode Bring power to pin 121 and try read again with nefmoto How did you read that eeprom file? Block 00: 1268301436daffffffffffffffff[ff5a] .h0.6......... .Z Desc ff18, Checksum Skip
Block 01: 050101007a8a0100030069c100a5[21fd] ....z.....i... !. Desc 0017, New Chksum [21fd]
Block 02: 050101007a8a0100030069c100a5[20fd] ....z.....i... . Desc 0117, New Chksum [20fd]
Block 03: 0401ffff00000000000000000000[fafd] .............. .. Desc 0207, New Chksum [fafd]
Block 04: 0401ffff00000000000000000000[f9fd] .............. .. Desc 0307, New Chksum [f9fd]
Block 05: 07026402d00107002104230cff2f[32fd] ..d.....!.#../ 2. Desc 0437, New Chksum [32fd]
Block 06: 00009c0d300e0000ffff00000000[15fd] ....0......... .. Desc 0533, New Chksum [15fd]
Block 07: 0504000000000000000000000000[f0ff] .............. .. Desc 06b7, New Chksum [f0ff]
Block 08: 0504000000000000000000000000[f0ff] .............. .. Desc 06f7, New Chksum [f0ff]
Block 09: 0080808080000080008080ff0000[78fb] .............. x. Desc 07b3, New Chksum [78fb]
Block 10: 0080808080000080008080ff0000[78fb] .............. x. Desc 07f3, New Chksum [78fb]
Block 11: 0405ffffff585858585800000000[37fb] .....XXXXX.... 7. Desc 08b7, New Chksum [37fb]
Block 12: 0405ffffff585858585800000000[37fb] .....XXXXX.... 7. Desc 08f7, New Chksum [37fb]
Block 13: 5858585858585858585858585800[7bfb] XXXXXXXXXXXXX. {. Desc 09b3, New Chksum [7bfb]
Block 14: 5858585858585858585858585800[7afb] XXXXXXXXXXXXX. z. Desc 09f3, New Chksum [7bfb]*
Block 15: 0000591a95b60000000000000000[0f0f] ..Y........... .. Desc 0ab3, New Chksum [33fe]**
Block 16: ffffffffffffffffffffffffffff[ffff] .............. .. Desc 0af3, New Chksum [fff1] *
Block 17: ffffffffffffffffffffffffffff[ffff] .............. .. Desc 0b32, Checksum Skip
Block 18: ffffffffffffffffffffffffffff[ffff] .............. .. Desc 0b10, Checksum Skip
Block 19: ffffffffffffffffffffffffffff[ffff] .............. .. Desc 0b10, Checksum Skip
Block 20: ffffffffffffffffffffffffffff[ffff] .............. .. Desc 0b10, Checksum Skip
Block 21: ffffffffffffffffffffffffffff[ffff] .............. .. Desc 0c37, New Chksum [f9f1]**
Block 22: ffffffffffffffffffffffffffff[ffff] .............. .. Desc 0d33, New Chksum [f8f1]**
Block 23: 0205000000000000000000000000[e2ff] .............. .. Desc 0e33, New Chksum [e2ff]
Block 24: 0000000000000000000000000000[e8ff] .............. .. Desc 0f33, New Chksum [e8ff]
Block 25: 0000000000000000000000000000[e7ff] .............. .. Desc 1033, New Chksum [e7ff]
Block 26: 0000000000000000000000000000[e6ff] .............. .. Desc 1133, New Chksum [e6ff]
Block 27: 0000000000000000000000000000[e5ff] .............. .. Desc 1233, New Chksum [e5ff]
Block 28: ffff384e30393036303138462020[7f09] ..8N0906018F .. Desc 1235, New Chksum [72fb]**
Block 29: 30303033ffffffffffffffffffff[3803] 0003.......... 8. Desc 1235, New Chksum [2af5]**
Block 30: 0102000000000000000b06000000[ceff] .............. .. Desc 13b7, New Chksum [ceff]
Block 31: 0102000000000000000b06000000[ceff] .............. .. Desc 13f7, New Chksum [ceff]
7 checksum(s) where corrected in this file.
■ Opening '95040origina2l.bin' file for writing
■ Writing to file
■ Validating size correct 512=512
■ All OK, closing file
7 checksum(s) where corrected in this file. |
|
|
|
« Last Edit: April 11, 2020, 02:26:16 PM by BlackT »
|
Logged
|
|
|
|
richo_vw
Newbie
Karma: +0/-0
Offline
Posts: 6
|
|
« Reply #2 on: April 12, 2020, 02:38:05 AM »
|
|
|
Upload your flash or send me to my PM I will compare it with ori, you can read it by galleto in boot mode
Bring power to pin 121 and try read again with nefmoto
How did you read that eeprom file?
I read the eeprom with argdub tool i tried the reading with power to Pin 121 but no luck
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP1281 session.
KWP1281 connect info: THIS-IS-THE-RAM-PROGRAM- [][]][][][]
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP2000 session.
Connected
Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Timing negotiation failed. Communications timings are unchanged.
Successfully changed to new communication timings.
Requesting security access.
ECU reports that security access is not supported.
Starting diagnostic session.
Successfully started diagnostic session.
Negotiating communication timings.
Successfully changed to new communications timings.
Requesting security access.
Security access granted
Validating flash memory starts at 0x00800000 and ends at 0x00880000
Validation failed, ECU reports RequestUpload service is not supported. ReuqestUpload may have been disabled bu aftermarket engine software:
Reading ECU flash memory failed.
100% complete.
Memory layout validation failed
I'll ask galleto to a friend who I think has one I don't mind to lose the tuned flash because because i don´t know the company (and the ecu come from a junkyard)and i want to start to tune by myself (on the bench by the moment) Could writing an ori and a new eeprom file be enough to start the immo-off like a normal ecu? Or do I need to do something else? Thanks |
|
|
|
« Last Edit: April 12, 2020, 03:12:03 AM by richo_vw »
|
Logged
|
patience please!!! newie ahead
|
|
|
|
BlackT
|
|
« Reply #3 on: April 12, 2020, 05:32:40 AM »
|
|
|
I
KWP1281 connect info: THIS-IS-THE-RAM-PROGRAM- [][]][][][]
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP2000 session.
Connected
Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Timing negotiation failed. Communications timings are unchanged.
Successfully changed to new communication timings.
Requesting security access.
ECU reports that security access is not supported.
Starting diagnostic session.
Successfully started diagnostic session.
Negotiating communication timings.
Successfully changed to new communications timings.
Requesting security access.
Security access granted
Validating flash memory starts at 0x00800000 and ends at 0x00880000
Validation failed, ECU reports
It is not stock, can you read ECU info? I will be good if you wont to put out file, yust in case Then flash stock file and free to go, On eepeom make immo off and check sum with ME7looger( you also need ME7EEPEOM) all you need is on this forum |
|
|
|
|
Logged
|
|
|
|
richo_vw
Newbie
Karma: +0/-0
Offline
Posts: 6
|
|
« Reply #4 on: April 12, 2020, 11:40:05 AM »
|
|
|
It is not stock, can you read ECU info?
Yes, I can read the ECU info without problems I have just written the ori (attached) via nefmoto, it throws some errors erasing memory sectors but at the end looks as a successful flash. The next step is find a eeprom file, do i need a specific 018F .bin or any ME7.5 will work? Is a dashboard adaptation or recode needed after eeprom flashing? or will the immo-off.bin stop the light from blinking in the dashboard? Thanks |
|
|
|
|
Logged
|
patience please!!! newie ahead
|
|
|
|
BlackT
|
|
« Reply #5 on: April 12, 2020, 11:46:29 AM »
|
|
|
You can try with eeprom file you read out.
Yust do immo off and check sum. Visal Me7looger can do it
Even you do immo off to ECU, you immo light will flash if your key is not matched with cluster. But car will start and drive normaly
|
|
|
|
|
Logged
|
|
|
|
|
_nameless
|
|
« Reply #6 on: April 12, 2020, 12:26:15 PM »
|
|
|
here yah go bub idk if you got a working version but this is it all set to go from your original
|
|
|
|
|
Logged
|
If you are in the market for a tune and would like the ease of downloading and flashing a dyno tested tune for a fair price check out https://instatune.sellfy.store/ |
|
|
richo_vw
Newbie
Karma: +0/-0
Offline
Posts: 6
|
|
« Reply #7 on: April 12, 2020, 01:10:50 PM »
|
|
|
Even you do immo off to ECU, you immo light will flash if your key is not matched with cluster. But car will start and drive normaly
Ok, i was not sure about that. As i have time because the quarantine and i haven't the car near of me to test if the immo-off works, my next steps will be around the cluster. I will try to find solution for the immo light, and to do a odometer correction,I have a new forged engine waiting to be installed after this time and i would like to set odo to 0 miles when it's done. I'll post it when I can try it Thank you here yah go bub idk if you got a working version but this is it all set to go from your original
thanks |
|
|
|
« Last Edit: April 12, 2020, 01:12:37 PM by richo_vw »
|
Logged
|
patience please!!! newie ahead
|
|
|
|
