totti
Full Member
Karma: +15/-29
Offline
Posts: 227
|
|
« Reply #30 on: August 14, 2019, 03:42:27 PM »
|
|
|
Use values of IMX from this file i dont see here overboosting But what i see is bad tuned KFMIRL
Your LDRXN at 5250 RPM is 175 % load --> 175% load and 5250 RPM tru KFMIOP in your map is about 90% tourqe request --> 90% tourqe at 5200 RPM tru KFMIRL in your map is around 160-165%
Soo at first you are requesting 175% load, but tru tourqe maps ecu calculated to request 165% load. And there all shit start to hapen, it has nothing to do with your IMX
So I should change LDRXN to 165 to limit rlmax?
|
|
|
Logged
|
|
|
|
BlackT
|
|
« Reply #31 on: August 14, 2019, 03:53:46 PM »
|
|
|
Sorry but can't anwer you precise without log with variables I tell you to log Also log ldrlts
|
|
« Last Edit: August 14, 2019, 03:58:05 PM by BlackT »
|
Logged
|
|
|
|
BlackT
|
|
« Reply #32 on: August 14, 2019, 04:11:08 PM »
|
|
|
Use values of IMX from this file i dont see here overboosting But what i see is bad tuned KFMIRL
Your LDRXN at 5250 RPM is 175 % load --> 175% load and 5250 RPM tru KFMIOP in your map is about 90% tourqe request --> 90% tourqe at 5200 RPM tru KFMIRL in your map is around 160-165%
Soo at first you are requesting 175% load, but tru tourqe maps ecu calculated to request 165% load. And there all shit start to hapen, it has nothing to do with your IMX
Forget about this calculation, without mifa and misol it can't be calculated it this way
|
|
|
Logged
|
|
|
|
totti
Full Member
Karma: +15/-29
Offline
Posts: 227
|
|
« Reply #33 on: August 14, 2019, 09:53:03 PM »
|
|
|
Sorry but can't anwer you precise without log with variables I tell you to log Also log ldrlts
I've logged all of the variables what you mentioned.
|
|
|
Logged
|
|
|
|
BlackT
|
|
« Reply #34 on: August 14, 2019, 10:52:01 PM »
|
|
|
Ahhhh.... Step 1 Change IMX to values you already have in you map when you don't have overboost Step 2 Flash you file to car Step 3 Take logs Step 4 post your logs and bin here
|
|
|
Logged
|
|
|
|
totti
Full Member
Karma: +15/-29
Offline
Posts: 227
|
|
« Reply #35 on: August 15, 2019, 01:12:53 AM »
|
|
|
Ahhhh.... Step 1 Change IMX to values you already have in you map when you don't have overboost Step 2 Flash you file to car Step 3 Take logs Step 4 post your logs and bin here
Ok that was my fault. I thought that you need these variables to tell the LDRXN value. I will do a log with the modified IMX table.
|
|
|
Logged
|
|
|
|
totti
Full Member
Karma: +15/-29
Offline
Posts: 227
|
|
« Reply #36 on: August 18, 2019, 09:23:53 AM »
|
|
|
HI,
I cannot reproduce the behaviour. Currently I've this logs with the bin.
|
|
|
Logged
|
|
|
|
nyet
|
|
« Reply #37 on: August 18, 2019, 10:38:46 PM »
|
|
|
I don't think your IRL is requesting enough load, rlsol is dropping off below rlmax
|
|
|
Logged
|
|
|
|
totti
Full Member
Karma: +15/-29
Offline
Posts: 227
|
|
« Reply #38 on: August 19, 2019, 03:55:11 AM »
|
|
|
I don't think your IRL is requesting enough load, rlsol is dropping off below rlmax
Why should I change IRL? What about change rlmax to lower? The requested boost curve is what I need.
|
|
|
Logged
|
|
|
|
nyet
|
|
« Reply #39 on: August 19, 2019, 09:36:24 AM »
|
|
|
Why should I change IRL? What about change rlmax to lower? The requested boost curve is what I need.
Sure, if you like. its better to implement taper with rlmax than IRL because IRL can get bumpy.
|
|
|
Logged
|
|
|
|
totti
Full Member
Karma: +15/-29
Offline
Posts: 227
|
|
« Reply #40 on: August 19, 2019, 10:05:55 AM »
|
|
|
Sure, if you like.
its better to implement taper with rlmax than IRL because IRL can get bumpy.
Thanks, so I should change LDRXN? If I know well this is the rlmax variable.
|
|
|
Logged
|
|
|
|
nyet
|
|
« Reply #41 on: August 19, 2019, 10:11:37 AM »
|
|
|
Yep.
|
|
|
Logged
|
|
|
|
BlackT
|
|
« Reply #42 on: August 19, 2019, 10:48:18 AM »
|
|
|
Why should I change IRL? What about change rlmax to lower? The requested boost curve is what I need.
Look at page before, i show you what values you need to change
|
|
|
Logged
|
|
|
|
totti
Full Member
Karma: +15/-29
Offline
Posts: 227
|
|
« Reply #43 on: August 19, 2019, 11:32:09 AM »
|
|
|
Look at page before, i show you what values you need to change
Thanks. But I don't want to more load at 6000rpm, that's why I would like to change rlmax(LDRXN) a little bit down.
|
|
|
Logged
|
|
|
|
BlackT
|
|
« Reply #44 on: August 19, 2019, 11:38:36 AM »
|
|
|
If you change rlmax, your misol will drop down. And that will result even worse intervention. You will need to put higher values in KFMIRL. Than you can lover down LDRXN
|
|
|
Logged
|
|
|
|
|