jessica997
Newbie
Karma: +0/-0
 Offline
Posts: 6
|
 |
« on: April 28, 2019, 12:51:47 AM »
|
|
|
Hi. Can I find someone who can help with injectors sizing with Laguna Coupe 2,0t?
|
|
|
|
|
Logged
|
|
|
|
aleks19411
Full Member
Karma: +4/-4
Offline
Posts: 60
|
|
« Reply #1 on: April 28, 2019, 08:41:48 AM »
|
|
|
write injector numbers..
|
|
|
|
|
Logged
|
|
|
|
jessica997
Newbie
Karma: +0/-0
Offline
Posts: 6
|
|
« Reply #2 on: April 30, 2019, 12:16:05 AM »
|
|
|
Original injectors Bosch 0280158195. New injectors Bosch 0280158211. Fuel pressure 3,5bar
|
|
|
|
|
Logged
|
|
|
|
aleks19411
Full Member
Karma: +4/-4
Offline
Posts: 60
|
|
« Reply #3 on: April 30, 2019, 12:30:34 AM »
|
|
|
EV14, 12 Ohm, 485cc, E 26°, Jetronic, O-O 34 mm, Long spray end, total 63 mm Bosch 0280158211
Maximum flow approx 485cc @ 3 bar
Short type injector (O-ring distance is 34 mm), long spray tip
Compatible with E85/RE85 and gasoline
14 mm O-rings, compatible with ethanol and gasoline
Jetronic (EV1)-type connector
High resistance
10 hole spray tip
Split type spray
Angle between connector and spray level 130 deg.
|
|
|
|
|
Logged
|
|
|
|
jessica997
Newbie
Karma: +0/-0
Offline
Posts: 6
|
|
« Reply #4 on: April 30, 2019, 03:18:43 AM »
|
|
|
Ok I know it :-) but i need help with modify file for New injectors :-)
|
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #5 on: April 30, 2019, 01:51:09 PM »
|
|
|
What's the problem?
|
|
|
|
|
Logged
|
|
|
|
aleks19411
Full Member
Karma: +4/-4
Offline
Posts: 60
|
|
« Reply #6 on: April 30, 2019, 02:05:24 PM »
|
|
|
join the question, what's the problem? constant?
|
|
|
|
|
Logged
|
|
|
|
jessica997
Newbie
Karma: +0/-0
Offline
Posts: 6
|
|
« Reply #7 on: April 30, 2019, 04:37:18 PM »
|
|
|
I dont know how to do this. This is my problem. Maybe someone can Tell me how can i make this mod or do this for me. Not for free...
|
|
|
|
|
Logged
|
|
|
|
|
Blazius
|
|
« Reply #8 on: April 30, 2019, 04:53:15 PM »
|
|
|
The question is do what  Are you looking for suggestions , or configuring the ecu for the new injectors ? If it uses ME7 ( which is what this forum is about) then you need to change KRKTE, and TVUB at minimum. |
|
|
|
|
Logged
|
|
|
|
|
nyet
|
|
« Reply #9 on: April 30, 2019, 05:30:53 PM »
|
|
|
I dont know how to do this. This is my problem. Maybe someone can Tell me how can i make this mod or do this for me. Not for free...
Have you read any of the fueling section of the s4 wiki? Done any injector research or study? Done anything at all to prep? |
|
|
|
|
Logged
|
|
|
|
|
prj
|
|
« Reply #10 on: May 03, 2019, 03:18:55 AM »
|
|
|
SAGEM3000 is nothing like a Bosch ECU... so most stuff on this forum will not be useful.
|
|
|
|
|
Logged
|
|
|
|
Ludo80
Newbie
Karma: +0/-0
Offline
Posts: 2
|
|
« Reply #11 on: December 28, 2019, 05:49:34 AM »
|
|
|
Hi, injectors lag time is used simultaneously on two correction maps. See below this map in 8 bits took from 2.0T 170hp dump , factor is 8 with zero offset. PM me if needed.  |
|
|
|
|
Logged
|
|
|
|
Ludo80
Newbie
Karma: +0/-0
Offline
Posts: 2
|
|
« Reply #12 on: December 28, 2019, 05:51:19 AM »
|
|
|
|
|
|
|
|
Logged
|
|
|
|
|
