|
1
on: Today at 11:33:12 AM
|
||
| Started by fredrik_a - Last post by Dannyhaddon | ||
|
Hello I am new here. I was looking for a logging software called "Open Moose". On its github it said that the software will be pushed in this forum but I haven't found it yet. Any clues? Or what other software do you use? Thanks  Can download at openmoose.net I've also got some 50wrhj and 50gphj multi map via cruise files if you want them. |
||
|
2
on: Today at 11:03:38 AM
|
||
| Started by shiousu - Last post by shiousu | ||
|
E2P
|
||
|
3
on: Today at 11:02:24 AM
|
||
| Started by shiousu - Last post by shiousu | ||
|
2001 VW PASSAT AUTO BIN AND MATCHING E2P
|
||
|
4
on: Today at 06:40:21 AM
|
||
| Started by bombis - Last post by bombis | ||
|
low wgdc at spool, why? imx super-weirdo also +3 deg advance @5000 is way too low wiki is pretty clear with tighten springs and all you need is KFVPDKSE axis, imx axis/values and DRL linearising (or imx linearising in case of precontrol way) Increased timing to 9,75@5000. why is it dropping 3-7deg occasionally? 0 ignition retard, dwkrz |
||
|
5
on: Today at 04:52:03 AM
|
||
| Started by bondango - Last post by bondango | ||
|
thanks and much appreciated, i will have a play with those.
|
||
|
6
on: Yesterday at 11:20:11 PM
|
||
| Started by bondango - Last post by Leonhard | ||
|
Basic specs:
charge time (Dwell) -> 2,0ms @ 14V (8,5 Ampere) for 60mJ charge time (Dwell) -> 2,6ms @ 14V (12 Ampere) for 90mJ Im using this Dwell voltage adjustment for aftermarket ECU: 8 10 12 14 16 18V 130 120 110 100 85 70% |
||
|
7
on: Yesterday at 02:55:02 PM
|
||
| Started by obdflasher - Last post by stranger | ||
|
What about TC1793 that doesn't seems to use CS2. Blocks still looks to be same size, but no block ID is used. Emulated eeprom is 192Kb in size. At place where normally CS2 is, only something similar to CS1. From TC1793 datasheet: Flexible CRC Engine (FCE). – IEEE 802.3 CRC32 ethernet polynomial: 0x82608EDB (CRC kernel 0). – CRC32C Castagnoli: 0xD419CC15 (CRC kernel 1). So, probably polynomial is one of this two... |
||
|
8
on: Yesterday at 02:53:01 PM
|
||
| Started by formaldegid - Last post by formaldegid | ||
|
This is EEPROM and FLASH files for ME7.5
BOSCH 0 261 207 204 VAG 06A 906 032 FC Skoda Octavia 1.8T gasoline engine AUM 2001 FLASH is 29F800BB marked as 0972877001 15.01.01 013_04 SL4 KWP1281 connect info: 1.8L R4/5VT G 0002 SoftCod: 11500, WSC: 00046 |
||
|
9
on: Yesterday at 01:55:18 PM
|
||
| Started by Beima - Last post by IVANVXR | ||
|
VW AXZ or BWS don't have standard schließzeitkennfeld , I think you must make custom code to cut spark in right time..any news here?
|
||
|
10
on: Yesterday at 12:04:21 PM
|
||
| Started by bombis - Last post by fknbrkn | ||
|
That solved the problem nyet Boost pressure follows boost pressure desired much better now low wgdc at spool, why? imx super-weirdo also +3 deg advance @5000 is way too low wiki is pretty clear with tighten springs and all you need is KFVPDKSE axis, imx axis/values and DRL linearising (or imx linearising in case of precontrol way) |
||