Dev Blog
Forum
Wiki
About
NefMoto
>
Noob Zone
>
Noob Questions
(Moderator:
turboat
) >
Timing not following
Pages: [
1
]
« previous
next »
Author
Topic: Timing not following (Read 5576 times)
4ringpieces
Full Member
Karma: +4/-4
Offline
Posts: 232
Timing not following
« on: March 07, 2015, 05:35:37 PM »
What is the map/correction factor name for timing vs iat? if there is one I've checked a few damos and cannot find anything around the timing maps
In my logs and my timing actual isn't following the kfzw/kfzw2 its about 5degrees off in places.
No knock cf's when this happens.
Iat's are going high tho 50-60celsius @6000rpm
Torque intervention turned off or on makes no difference, but found with torque intervention off I had less knock cf's when abusing the car but slightly more spikey boost control.
Throttle is staying @100 during the run
Car does have an over-reading maf sensor as there's no way this 1.8t ko3 is pulling 210g/s when its boosting 1.3bar, This will be changed soon so hopefully this is the problem. But i'm wondering if i'm missing something else?
Logged
Lost
Hero Member
Karma: +21/-14
Offline
Posts: 556
Re: Timing not following
« Reply #1 on: March 08, 2015, 01:22:17 AM »
If you mean that actuall in the logs is a bit higher than the values you have in kfzw/2 ??
It Is bc kfzw/2 is trying too come up too timing optimal kfzwop/2.
Logged
nyet
Administrator
Hero Member
Karma: +604/-166
Offline
Posts: 12235
Re: Timing not following
« Reply #2 on: March 08, 2015, 01:25:04 AM »
Quote from: Mocke on March 08, 2015, 01:22:17 AM
If you mean that actuall in the logs is a bit higher than the values you have in kfzw/2 ??
It Is bc kfzw/2 is trying too come up too timing optimal kfzwop/2.
No. Please don't present wild guesses as conclusive answers
OP: Please post logs.
Logged
ME7.1 tuning guide
(READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x
Please do not ask me for tunes. I'm here to help people make their own.
Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
4ringpieces
Full Member
Karma: +4/-4
Offline
Posts: 232
Re: Timing not following
« Reply #3 on: March 08, 2015, 02:46:40 AM »
Logs are just poor vcds ones tbh nyet
Timing was much lower than kfzw, only reason I could see was iat its over 40-50deg c and the maf over reads
kftarx I did modify to counter the heat from the amount of load on long pulls at high rpm by dropping it down. but can this affect the timing aswell? Even when torque monitoring is off?
Maybe just a bad maf but thought I'd check
Logged
Lost
Hero Member
Karma: +21/-14
Offline
Posts: 556
Re: Timing not following
« Reply #4 on: March 08, 2015, 04:41:37 AM »
Quote from: nyet on March 08, 2015, 01:25:04 AM
No. Please don't present wild guesses as conclusive answers
OP: Please post logs.
When you start a sentence with "If" , it is an assumption. Not conclusion. You should know that master N. Anyway - we always have you too straight us upp
Logged
nyet
Administrator
Hero Member
Karma: +604/-166
Offline
Posts: 12235
Re: Timing not following
« Reply #5 on: March 08, 2015, 02:22:17 PM »
Quote from: Fordy on March 08, 2015, 02:46:40 AM
Logs are just poor vcds ones tbh nyet
You won't be able to fix anything w/o proper logs.
Quote
Even when torque monitoring is off?
I doubt torque monitoring is "off"
Quote
Maybe just a bad maf but thought I'd check
Log, don't guess.
Logged
ME7.1 tuning guide
(READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x
Please do not ask me for tunes. I'm here to help people make their own.
Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
vwaudiguy
Hero Member
Karma: +53/-37
Offline
Posts: 2024
Re: Timing not following
« Reply #6 on: September 14, 2015, 10:59:35 AM »
Any updates on this, Fordy? I'm having a similar issue.
Logged
"If you have a chinese turbo, that you are worried is going to blow up when you floor it, then LOL."
nyet
Administrator
Hero Member
Karma: +604/-166
Offline
Posts: 12235
Re: Timing not following
« Reply #7 on: September 14, 2015, 11:02:20 AM »
Quote from: vwaudiguy on September 14, 2015, 10:59:35 AM
Any updates on this, Fordy? I'm having a similar issue.
Post logs.
Logged
ME7.1 tuning guide
(READ FIRST)
ECUx Plot
ME7Sum checksum checker/corrrector for ME7.x
Please do not ask me for tunes. I'm here to help people make their own.
Do not PM me technical questions! Please, ask all questions on the forums! Doing so will ensure the next person with the same issue gets the opportunity to learn from your experience.
adam-
Hero Member
Karma: +122/-33
Offline
Posts: 2178
Re: Timing not following
« Reply #8 on: September 14, 2015, 01:13:18 PM »
There should be a requirement to post logs.
This thread is just going round in circles.
Logged
Pages: [
1
]
Print
« previous
next »
Jump to:
Please select a destination:
-----------------------------
General
-----------------------------
=> Introductions
=> General Discussion
-----------------------------
Noob Zone
-----------------------------
=> Noob Questions
=> Noob Guides and FAQs
-----------------------------
Technical
-----------------------------
=> NefMoto Software
=> Tuning
===> Documents & Helpers & How To's
===> Community Projects
=> Diagnostics
=> Flashing and Chipping
=> Cluster and Immobilizer
===> ECU EEPROM images
===> Original Cluster dumps
===> Original Cluster dump requests
=> Data Logging
=> Reverse Engineering
=> Communication Protocols
-----------------------------
ECU Files
-----------------------------
=> ECU Definition Files
===> ECU Definition File Requests
=> Original ECU Files
===> Original ECU File Requests
=> Checksum Update Requests
-----------------------------
Vehicles
-----------------------------
=> Vehicle Tech
=> Project Cars
-----------------------------
Regional
-----------------------------
=> Canadian Regional Discussion
=> US Regional Discussion
-----------------------------
Classifieds
-----------------------------
=> For Sale
=> Wanted
=> Services
-----------------------------
Miscellaneous
-----------------------------
=> Off Topic
=> Forum Tech Support
=> Bizarro Messages Posted by Bots and Spammers
Navigation
Home
Help
Login
Register
Personal Tools
May 07, 2024, 03:46:12 AM
Welcome,
Guest
. Please
login
or
register
.
Did you miss your
activation email?
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
Search
Advanced Search
Loading...
