pathanas
Newbie
Karma: +0/-0
Offline
Posts: 14
|
|
« on: September 04, 2018, 10:47:50 PM »
|
|
|
Hello,I am working on my audi tt 1.8 and getting some retards on high RPM. My trims are near 1 on idle and part Is that from knock sensor voltages?
|
|
« Last Edit: September 24, 2018, 12:35:26 PM by pathanas »
|
Logged
|
|
|
|
aef
|
|
« Reply #1 on: September 05, 2018, 04:34:57 AM »
|
|
|
upload the untouched csv
|
|
|
Logged
|
|
|
|
pathanas
Newbie
Karma: +0/-0
Offline
Posts: 14
|
|
« Reply #2 on: September 05, 2018, 04:54:43 AM »
|
|
|
ΟΚ
|
|
|
Logged
|
|
|
|
spacey3
Full Member
Karma: +12/-1
Offline
Posts: 198
|
|
« Reply #3 on: September 05, 2018, 05:04:45 AM »
|
|
|
What did you use to log? The logfile is pretty awful.
Retard doesn't look that bad though, just pull a bit of timing...?
Boost is way over the map sensor also I see...
|
|
|
Logged
|
|
|
|
pathanas
Newbie
Karma: +0/-0
Offline
Posts: 14
|
|
« Reply #4 on: September 05, 2018, 06:09:57 AM »
|
|
|
I used me7 logger.that is my first log :)I was using vag com A have a gtx2867 and on this log I am hitting 30,5 psi of boost on 7200rpm. I was thinking to enrich a little on red line to avoid the retard corrections at first...?
|
|
|
Logged
|
|
|
|
pathanas
Newbie
Karma: +0/-0
Offline
Posts: 14
|
|
« Reply #5 on: September 05, 2018, 06:26:05 AM »
|
|
|
I just trying to find the reason of that retard,the knok voltages are not more than 30v EGT and IAT are not too high.
|
|
« Last Edit: September 05, 2018, 06:30:18 AM by pathanas »
|
Logged
|
|
|
|
nyet
|
|
« Reply #6 on: September 05, 2018, 08:44:37 AM »
|
|
|
Why are your separators ; and not commas?
A lot of those values are plain wrong, are you sure you are using the right .ecu definition for your bin?
|
|
|
Logged
|
|
|
|
adam-
|
|
« Reply #7 on: September 05, 2018, 09:36:26 AM »
|
|
|
It's been editted/cut. I bet foreign/incorrect CSV format.
|
|
|
Logged
|
|
|
|
pathanas
Newbie
Karma: +0/-0
Offline
Posts: 14
|
|
« Reply #8 on: September 05, 2018, 09:59:45 AM »
|
|
|
The file is exactly how it's been saved from logge, I did only delete the first lines information On the ecu definitions for the ecu do you mean these I am using on winols?
In order to create the tamplate file I used the modified bin
|
|
|
Logged
|
|
|
|
nyet
|
|
« Reply #9 on: September 05, 2018, 10:52:22 AM »
|
|
|
The file is exactly how it's been saved from logge, I did only delete the first lines information
Please do NOT UPLOAD EDITED CSVs On the ecu definitions for the ecu do you mean these I am using on winols?
In order to create the tamplate file I used the modified bin
The values you are logging are very wrong. Something is amiss.
|
|
|
Logged
|
|
|
|
pathanas
Newbie
Karma: +0/-0
Offline
Posts: 14
|
|
« Reply #10 on: September 05, 2018, 11:18:40 AM »
|
|
|
What do you mean by edited cvs? What was edited?
|
|
|
Logged
|
|
|
|
nyet
|
|
« Reply #11 on: September 05, 2018, 12:17:48 PM »
|
|
|
What do you mean by edited cvs? What was edited?
I did only delete the first lines information
|
|
|
Logged
|
|
|
|
aef
|
|
« Reply #12 on: September 05, 2018, 12:47:41 PM »
|
|
|
only use ecuxplot to open the logs and nothing more
not necessary to delete something from the file
|
|
|
Logged
|
|
|
|
pathanas
Newbie
Karma: +0/-0
Offline
Posts: 14
|
|
« Reply #13 on: September 05, 2018, 01:00:22 PM »
|
|
|
only use ecuxplot to open the logs and nothing more
not necessary to delete something from the file
ok thank you, i will try again
|
|
|
Logged
|
|
|
|
nyet
|
|
« Reply #14 on: September 05, 2018, 01:09:05 PM »
|
|
|
I bet foreign/incorrect CSV format.
Yea, for languages that use commas instead of decimal places, csvs end up semi-colon separated. In any case, that isn't a problem, ECUxPlot can handle semicolons. the problem is most of the values logged are completely wrong.
|
|
|
Logged
|
|
|
|
|