NefMoto

Hi Guys. I am totally new to this, hence i need some guidance on this. My ride is a 2004 VW Touareg 3.2 V6 and I am using the "Blue" KKL FT232R cable and have trouble running "Full Flash Read". FYI, i initially tried the 29F800BB memory layout & failed, hence i tried all other memory layouts available with the application and still failed. Below are my logs in Nefmoto (V 1.9.3.2) with a 29F800BB memory layout.

Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP2000 session.
Connected
Disabling Windows sleep mode.
Reading all ECU info.
Starting diagnostic session.
Unable to properly start diagnostic session, attempting to continue with current undefined session.
Negotiating communication timings.
Successfully changed to new communication timings.
0% complete.
20% complete.
40% complete.
60% complete.
80% complete.
100% complete.
Read 5 ECU info entries:
   0x92, System Supplier ECU Hardware Number: 0261208647
   0x94, System Supplier ECU Software Number: 1037371625
   0x91, Vehicle Manufacturer ECU Hardware Number: 0x0D,             , 0xFF
   0x9B, Calibration Date: 022906032GA , 6384, 0x03000085, 0x00000000, 0x7AB6, MOTRONIC ME7.1., 1G   
   0x9C, Calibration Equiment Software Number: 0x02000000
Restoring Windows sleep mode.
Disabling Windows sleep mode.
Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
Security access granted.
Starting diagnostic session.
Successfully started diagnostic session.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
Security access granted.
Validating flash memory starts at 0x00800000 and ends at 0x00900000.
Validation failed, ECU reports RequestUpload service is not supported. RequestUpload may have been disabled by aftermarket engine software.
Memory layout validation failed.
Starting to read data block.
Requesting upload from ECU for address range 0x00800000 to 0x00803FFF.
Request upload from ECU failed, ECU reports service is not supported. Request upload may have been disabled by aftermarket engine software.
Reading ECU flash memory failed. Trying to force ECU to recognize read operation is complete.
Finished forcing ECU to recognize that failed read operation is complete.
Reading ECU flash memory failed.
100% complete.
Restoring Windows sleep mode.
Disconnecting...
Disconnected

It keep stating that "aftermarket engine software" is blocking. As i know, this is a totally stock ECU which has not been flashed before.

Nefmoto does not work on many newer ecus. You can try again with the baud rate set at 38400 AFTER you connect, however it likely just won't work.

https://www.google.com/search?q=galletto+v53&client=safari&sa=X&hl=en-us&biw=375&bih=559&tbs=vw:l&tbm=shop&prmd=isvn&srpd=18074875902804817030&prds=num:1,of:1&ved=0ahUKEwjX0vT7mc7LAhUFMyYKHR5MCmQQgjYItwQwAw&ei=6QjuVpe6H4XmmAGemKmgBg
This will do the trick

So in other words the KKL cable cannot be used for the Touareg at all.

Appreciate the help guys. Thanks.

You can PROBABLY write the ecu with nefmoto. 38400 baud. Make a full backup before attempting though.

I can confirm that Nefmoto will write 022906032BF 04 Touareg VR6. I couldn't get it to read with Nefmoto, but MPPS did in boot mode.....but there is an ORI file posted here if you search. I also needed this http://nefariousmotorsports.com/forum/index.php?topic=6719.0