|
Title: Audi A4 B5: Help with IMMO PIN from 95040 Read Post by: locutas on August 05, 2016, 08:37:10 AM Hello,
I was able to read my immo (Audi A4 B5 ECU 8D0906018E) using Argdub's EEPROM reader. Problem is I can't seem to identify the PIN/SKC from the .bin file. The relevant lines contain FF FF and nothing else. Kindly advise if I'm doing something wrong and assist with extracting the PIN/SKC from the attached file. Many thanks. Title: Re: Post by: macxxx on August 05, 2016, 12:31:14 PM Probably Immo2 so there is no pin in ecu
Engine code is ARG? Title: Re: Post by: locutas on August 06, 2016, 12:13:24 PM Probably Immo2 so there is no pin in ecu Engine code is ARG? No. Engine is APT. Title: Re: Post by: macxxx on August 06, 2016, 10:21:47 PM Ok doesn't matter the code ;)
check 17-instruments using vcds/vagcom , if there is only immo id ( AUZ... etc ) a no VIN then it's immo2 for sure. Title: Re: Audi A4 B5: Help with IMMO PIN from 95040 Read Post by: EuroXs4 on August 18, 2016, 06:02:22 PM Locutas this looks like a virgin dump rather than a read from your ecu. no vin or immo id either.Pin looks to be 0001.But the dump looks to be incomplete.Is this a european ecu??
I Title: Re: Post by: macxxx on August 18, 2016, 09:51:06 PM It's from ecu
Title: Re: Post by: Shabangabang on October 06, 2016, 06:37:30 AM Hi guys
I'm posting here because i have a 2000 Audi A4 B5 that I just cannot seem to read the 95040 Bin with Argdubs Tool. Below is the response i'm getting. I have been able to pull the Instrument Cluster Eprom dump (attached) using the VAG K Comander Lead and software version 1.4 which is 2048k . I have run this through the eeprom tool but the tool has problems parsing the 2k bin file. I have had no luck getting the ECU Eprom Dump usign the VAG K Commander. All i really want is to get the SKC code from the BIN file so i can replace the only key i lost for my Audi Avant. Like most punters i'm loth to pay the $800 for a key to be sent from Germany to Australia. Can the SKC code be read from the 2048k Instrument Cluster Bin? If so which blocks do i need to read?? C:\Users\sheldon\Desktop\EpromBoot\argdubsTool>me7_95040.exe --OBD -r -p4 eeprom .bin Ver: 1.31 Com Port: 4 Baud Rate: 10400 Opening COM4 ... OK Initiating communication ... OK ECU ID response: 3B0907552P 2.4L V6/5V G 0001 SoftCod: 04551, WSC: 20690 Reading EEPROM ................................................................. FAIL. (error=0x01) Closing COM4 Title: Re: Post by: macxxx on October 06, 2016, 06:54:21 AM The pin must be in the cluster dump...it is 3 times repeated in the end...im writing from tapatalk i can check it later
Title: Re: Post by: macxxx on October 06, 2016, 01:56:55 PM 6A1A - swap byte 1A6A - DEC 6762 so your PIN is 6762 You have immo2 so reading Epprom from ecu wouldn't help you... Title: Re: Audi A4 B5: Help with IMMO PIN from 95040 Read Post by: Shabangabang on October 10, 2016, 06:28:24 AM Hi Macxx
Thanks for your quick reply on the question of how to establish the SKC from the immobilizer bin file. I saw another post that also confirmed to look for the hex reference repeated 3 times in the immobilizer cluster bin file. I did try the code in VCDS under the "immobilizer section / Login" section but VCDS would not except the code for some reason. I was hoping to confirm the details of the currently configured but lost key in VCDS. I'm waiting for a immo 2 key fob to come in the mail soon so will try again shortly. I have also purchased the 5.5 Vag K Commander Cable with the hopes of being able to pull the ECU' bin. I cannot work out why i cannot receive the ECU bin after establishing a connection. Title: Re: Post by: macxxx on October 10, 2016, 08:13:15 AM Try to change the latency time in Windows setting of com port to 1ms
|