|
Title: VAG Can Pro with Ross Tech cable Post by: lissy on May 26, 2017, 03:21:31 AM Helllo :-)
first of all I want to thank everyone for taking the time to answer all the questions and write all the helpful FAQs :) But I have another question and I could not find the answer with the search function. I do not know if you guys know VAG Can Professional https://www.k-electronic-shop.de/AUDI/AUDI-A1/AUDI-A1-8X/VCP-VAG-Can-Professional-Diagnose-Interface-v2-0.html I have a genuine Ross Tech cable for VCDS. Is it possible to use the cable in dumb mode with VAG Can Pro software? I want to change the settings for Adaptive Air Suspension in my Audi A7. I know I can do that also with VCDS. The main difference here is, that i must measure all wheels and do this on flat ground. VCDS has also limits regarding lowering the Air Suspension. With VCP (this is the short name of VAG Can Pro) I could directly set the desired height and I also can configure this for every driving mode independently (comfort, dynamic, ...). Here is the description from the website: Quote WABCO Programmer Sorry for the german description, I will translate the important points:Das WABCO Programmier Addon ist ein Konfigurationstool für Audi Adaptive Air Suspension (AAS). Durch Anpassungen im EEPROM werden so umfangreiche Anpassungsmöglichkeiten für den Benutzer ermöglicht. Unter anderem kann so die Fahrwerkshöhe direkt als Abstandswert (+ / - ) ohne aufwändiges Anfahren über die Grundeinstellung gesetzt werden. Anpassungsmöglichkeit ebenso bei welchen Geschwindigkeiten welche Fahrwerksanpassung vollzogen werden soll bzw. in welchen Fahrmodi welche Fahrwerkshöhe gewünscht ist (Sport, Normal, Lift) The WABCO programming addon is a tool for configuring Audi AAS. You can change the suspension height directly in EEPROM without executing a basic adjustment for the suspension. It is also possible configure each modes (dynamic, comfort, lift) indendently and depending on vehicle velocity. Thats all, if you know another software which could do the same this would make me happy too :-) I do not know another possibility :-( Title: Re: VAG Can Pro with Ross Tech cable Post by: prj on May 26, 2017, 07:35:32 AM No, you have to buy the interface.
That said, it's very cheap for what it is. Title: Re: VAG Can Pro with Ross Tech cable Post by: aef on May 26, 2017, 08:52:48 AM try to find owners of vcp in your location
there are facebook groups for vcp and you can have a look into kleinanzeigen.ebay.de Title: Re: VAG Can Pro with Ross Tech cable Post by: lissy on May 26, 2017, 09:10:20 AM No, you have to buy the interface. Yea maybe but VCDS covers most of the functionality and it is very expensive to pay 300 euros only for coding AAS :-)That said, it's very cheap for what it is. @aef yes thanks i thought it would be possible because i want to have it myself. I do not want to ask other people all the time :-) So well, then i will buy the interface. Not best whay to spend 300 euros but if there is no other solution for that ... :( Title: Re: VAG Can Pro with Ross Tech cable Post by: vwaudiguy on May 26, 2017, 02:02:49 PM Title: Re: VAG Can Pro with Ross Tech cable Post by: cherry on May 26, 2017, 04:20:54 PM VCP will not work for A6/A7 modell 4G! It´s only working for A6 4F, A8 4E, Q7 4L and Toureg 7L. For Wabco and some older Conti modules.
Anyway if you want to go flat just change coupling rods or install expensive piggyback module. With manipulating basic setting you can only achieve 15mm. And take care that you go down equally front and rear axle or you will get errors from camera, acc, etc... |