|
Title: Help clearing DTC errors APY to BAM S3 Post by: pompak on August 13, 2017, 05:25:48 AM Hello.
I need help with the Audi S3 1.8T APY 210 ps. Orginally there is a computer with 512kb memory and a narrowband lambda sensor. I changed the computer to BAM 1024 kb with a broadband lambda probe, put the wires into the ECU, everything works, the map was made, Audi accelerates about 5.8s to 100km / h. Unfortunately I have DTC errors and I can not turn them off, will somebody help me? Ecu immo off Exactly: 17526 - Oxygen Lambda Sensor Heating B1 S2: Open Circuit P1118 - 35 - 17939 - Camshshaft Timing Adjustment: Open Circuit P1531 - 35 - 18058 - Powertrain Data Bus: Missing Message from Instrument Cluster P1650 -35- 17863 - Exhaust Gas Temp Sensor 1 (G235): Implausible Signal P1455 -35- Sometimes there are also: 17705 / P1297 / 004759 - Pressure Drop between Turbo and Throttle Valve (check D.V.!) Auto then loses power, DV replaced, leak tested, where does that come from? I would ask for help removing the DTCs from the map or possibly throwing them out of ECU Lambda 2 and Exhaust Gas Temp, and Camshaft. Regards, I attach the current flash Title: Re: Help clearing DTC errors APY to BAM S3 Post by: _nameless on August 13, 2017, 05:45:48 AM All of thst is covered in the s4 wiki aside from missimg message. That qill be error class. Tho it wont throw a cel or affect anything. The other ones qill throw a cel and youll loose ltft
Title: Re: Help clearing DTC errors APY to BAM S3 Post by: pompak on August 21, 2017, 09:03:45 AM Thanks, I learned a lot from this site, I erased DTC errors and egt sensor, but there is another problem after running about 1km appears:
16396 - Bank 1 Camshaft A (intake) Advance Setpoint not Reached (Over-Retarded) P0012 -35 - What do I have to change in the map to not display this error? I do not understand the description of s4 wiki VVt with DTC is erased, probably loses power as this error occurs Title: Re: Help clearing DTC errors APY to BAM S3 Post by: aef on August 22, 2017, 02:45:30 AM Have you tried ESKONF to tell the ecu what is installed and what is not installed hardware wise?
Title: Re: Help clearing DTC errors APY to BAM S3 Post by: sonique on August 22, 2017, 08:56:28 AM Hello. I need help with the Audi S3 1.8T APY 210 ps. Orginally there is a computer with 512kb memory and a narrowband lambda sensor. I changed the computer to BAM 1024 kb with a broadband lambda probe, put the wires into the ECU, everything works, the map was made, Audi accelerates about 5.8s to 100km / h. Unfortunately I have DTC errors and I can not turn them off, will somebody help me? Ecu immo off Exactly: 17526 - Oxygen Lambda Sensor Heating B1 S2: Open Circuit P1118 - 35 - 17939 - Camshshaft Timing Adjustment: Open Circuit P1531 - 35 - 18058 - Powertrain Data Bus: Missing Message from Instrument Cluster P1650 -35- 17863 - Exhaust Gas Temp Sensor 1 (G235): Implausible Signal P1455 -35- Sometimes there are also: 17705 / P1297 / 004759 - Pressure Drop between Turbo and Throttle Valve (check D.V.!) Auto then loses power, DV replaced, leak tested, where does that come from? I would ask for help removing the DTCs from the map or possibly throwing them out of ECU Lambda 2 and Exhaust Gas Temp, and Camshaft. Regards, I attach the current flash you are plz read more this site and find the solution and you are runing w/o egt sensor and not use BTS fueling short time melt the engine |