NefMoto

Hello i have poblem with overrun in BAM engine. In AUM i do like this:
KFNWEGM set to max rpm
KFTVSA decrease a litlle bit some value
KFTVSAKAT set 1 for row with a 900c grad
KFZWMN set to -19 from 4500 rpm to max on bigger load

Work pefect in aum in BAM a try everythink, CWSAWE set to 1 etc doesnt work. Whats its problem ?

Can you upload both bin files, or screenshots of the mentioned tables.

From this BAM, doesnt work...

At what load did you set KFZWMN to -19?

Set At the highest load, in AUM work perfect...

Firstly. Negative timing should be set at low to medium-low load, if at all needed.

Secondly. That doesn't look like KFZWMN, and why aren't your axis defined?
How do you know where and what you are changing?

And as a little sidenote; why did you set KFNWEGM to max RPM?

why did you increase KFZWMN on medium-low load ?

What is load when you lift?

Clue: it's not 240.

this it not good ;)

1. http://nefariousmotorsports.com/forum/index.php?topic=7174.105 - KFNWEGM  someone say set to max bla bla bla...
2. Axis ? doesnt care... its not a problem.

From aum and works pefect only when above 4500... but this solution doesnt work in BAM...

there is a world of difference between two files..
AUM file is ok but BAM file very bad

Yep there is a good answer bro thanks :) So let's start...
KFNWEGM - aum go to hifg rpm work / BAM ?
KFTVSA decrease a litlle bit some value, BAM ? Whats its problem ? To long time or what ?
KFTVSAKAT set 1 for row with a 900c grad / BAM ?
KFZWMN set to -19 from 4500 rpm to max on bigger load - this its intrested you say to put -value in lowest load ? I wouldn't have this staff on lowest rpm ! Only when ride above 4500/ BAM file where is the problem  ?

CWSAWE  in AUM doesnt touch / in BAM ? :O

1. KFNWEGM is resume engine speed map, And not really needed for overrun.
This is also mentioned somewhere in that thread.

2. But it seems like you are having problems?

yes because see the different

And you thinking it is problem ?

KFZWMN  on my file from BAM is adres 1756C right ? I change axis etc set this and try.

Other thinks ?

KFNWEGM - ?
KFTVSA - ?
KFTVSAKAT - dont touch ?
KFZWMN -I now
CWSAWE   - 01

Think what you're trying to achieve.  You are not at 150+ load when you lift.

+1000000

your AUM KFZWMN map  wrong  /not only this one/
you are set low load working
bam map fine set high load and not work :D
not need any axis change

100001

And other what about other ?

KFNWEGM - ?
KFTVSA - its funny someone say set right this someone say right this... whats time is it ? And tell me why in AUM have lowest value then BAM
KFTVSAKAT - on high temp set 1 ?
CWSAWE   - 01

I already explained KFNWEGM.
KFTVSA is overrun in seconds.
KFTVSAKAT is overrun in milliseconds at given cat temperature.

I think your definition is bad.

Whose DEFINITION IS BAD ? KFZWMN after my change its ok ?

If the image you posted is what you changed it to, then it should be fine.

Ok i write this but still doesnt have pops...

Are you absolutely sure you have located KFZWMN correctly?
Cause when I look at the map you are changing, it doesn't look right

It's possible, my adress is 1756C

Any ideas ? I think my KFZWMN have a good adress.