|
Title: Flashing,VW Lupo, 2001, 1.0L, AUC Post by: GMB on May 02, 2018, 12:00:57 PM Hello people! My name is Gabriel.
I am new to flashing ECUs. My goal is to flash a car, which is a VW Lupo, 2001, 1.0L, AUC engine, Bosch Motronic ECU, ME7.5.10. The car has got a problem, related to acceleration, mainly but not only that. The car starts but does not accelerate, and if i insist to press the acceleration pedal in about 10 sec. it shows up o the dashboard, the Check and EPC lights. When that happens, it allows you to accelerate up to 2200-2500rpm maximum. It gives a permanent error on Throttle Actuator, and Lambda Senzor, but other intermitent ones get added while engine runs(about 10-12). I tested everything on the electrical diagram, wires, voltages, earth connections, replaced Throttle Module and Acceleration Pedal, but no change. My impression is that there is a corrupt memory inside the ECU. Is it possible to have the right memory flas file, for the car? I have got a KKL interface, and already installed NefMoto flasfing software. The memory layout is: ME7 229F400BB. Thank you!Best regards! Title: Re: Flashing,VW Lupo, 2001, 1.0L, AUC Post by: adam- on May 02, 2018, 12:56:47 PM Rear 02 shorted out?
Title: Re: Flashing,VW Lupo, 2001, 1.0L, AUC Post by: GMB on May 02, 2018, 12:58:16 PM Hello!
My name is Gabriel. I am new to flashing ECUs. My goal is to flash a car, which is a VW Lupo, 2001, 1.0L, AUC engine, Bosch Motronic ECU, ME7.5.10. The car has got a problem, related to acceleration, mainly but not only that. The car starts but does not accelerate, and if i insist to press the acceleration pedal in about 10 sec. it shows up o the dashboard, the Check and EPC lights. When that happens, it allows you to accelerate up to 2200-2500rpm maximum. It gives a permanent error on Throttle Actuator, and Lambda Senzor, but other intermitent ones get added while engine runs(about 10-12). I tested everything on the electrical diagram, wires, voltages, earth connections, replaced Throttle Module and Acceleration Pedal, but no change. My impression is that there is a corrupt memory inside the ECU. Is it possible to have the right memory flas file, for the car? I have got a KKL interface, and already installed NefMoto flasfing software. The memory layout is: ME7 229F400BB. Thank you!Best regards! Title: Re: Flashing,VW Lupo, 2001, 1.0L, AUC Post by: GMB on May 02, 2018, 01:09:00 PM Rear 02 shorted out? Only Bank 1, O2 fault code appears. Thank you! Title: Re: Flashing,VW Lupo, 2001, 1.0L, AUC Post by: adam- on May 02, 2018, 01:16:52 PM Any other codes?
Title: Re: Flashing,VW Lupo, 2001, 1.0L, AUC Post by: GMB on May 02, 2018, 11:15:16 PM Any other codes? Throttle Actuator, under voltage during basic settings. This and Lambda sensor 1 open circuit are Permanent. Another one, Throttle control unit, malfunction, intermittent. I also tried to do -Throttle basic settings- and it gave me error. These appear first and after a while since the engine started many others appear...up to 12 errors! Thank you! Title: Re: Flashing,VW Lupo, 2001, 1.0L, AUC Post by: adam- on May 02, 2018, 11:50:08 PM Check that loom.
Title: Re: Flashing,VW Lupo, 2001, 1.0L, AUC Post by: GMB on May 02, 2018, 11:54:04 PM |