|
Title: help with rear 02's mk4 r32( have some locations already) Post by: up50lut3 on July 29, 2018, 11:58:11 PM hey all,
i can't find a damos or xdf for my ecu.. ive tried others to compare but to no avail. I still have the rear 02's but no cats. i can either delete them or numb them to go through emissions but i cant figure out which bit is what for ither situation anyone with a little insight as to whats what would be much appreciated 0x18194 is where control bits start. i have the are where the control bits are but cant find the correct addresss for You maybe able to numb ME7's sensitivity (note: untested) using: [55][56] AHKATMN (0x18672) - leave alone AHKATMX (0x18673) - set to max AHKATS (0x18674) - set to max AHKATSB (0x18675) - set to max ....or CDHSH - Post cat O2 heater diagnosis CDHSHE - Post cat O2 heater amplifier diagnosis CDLATV - Lambda sensor aging diagnosis (tv) in OBDII-Mode (inverse: EURO-Mode) CDLASH - Lambda sensor aging diagnosis (SHK) in OBDII-Mode (inverse: EURO-Mode) CDLSH - Post cat O2 sensor diagnosis CDLSHV - Lambda sensor sensor interchange recognition (N/A for vehicles equipped with a single post cat sensor, IE 1.8t and certain vr6) CWKONLS (0x181BB) - Vehicles with 4 installed sensors - change from 51 (0x33/00110011b) to 17 (0x11/00010001b)[58] Vehicles with 2 installed sensors (default value 3), set to 1. When setting CWKONLS CDLSH must also be configured to prevent malfunction in circuit DTC's. CWKONLS.1 = 0 CWKONLS.5 = 0 Change these to disable rear O2 lambda control:[59][60] CLRHK (0x11A87) - Code word for Lambda - Bit 0 is Control post cat on/off. Set bit 2 and 0, clear bit 3 to disable; i.e. set from 72 (0x48/01001000b) to 5 (00000101b)[61] CLRHK.0 = 1 CLRHK.2 = 1 CLRHK.3 = 0 CLRHK.6 = 0 (don't care) CLRSHK - Wideband vehicles use CLRSHK. In these the default value is typically 16 (0x10/0001000b). Set bit 0 (and possibly set bit 2 and clear bit 3?) to disable (set to 5?) CLRSHK.0 = 1 CLRSHK.2 = 1(?) unconfirmed. CLRSHK.3 = 0(?) unconfirmed. CLRKA (0x11A72) - set to 0[62] Title: Re: help with rear 02's mk4 r32( have some locations already) Post by: J.Laborde on July 30, 2018, 12:09:25 AM Hey Mate,
I'll take a look at your file in a few hours, and export a map pack with all the maps you're after :) ~ J.Laborde Title: Re: help with rear 02's mk4 r32( have some locations already) Post by: up50lut3 on July 30, 2018, 12:30:35 AM love you.... no homo lol
::) ::) Title: Re: help with rear 02's mk4 r32( have some locations already) Post by: up50lut3 on July 30, 2018, 04:12:08 PM love you.... no homo lol ::) ::) so i guess that was bs..... :(( Title: Re: help with rear 02's mk4 r32( have some locations already) Post by: J.Laborde on July 30, 2018, 05:58:42 PM Hey mate,
Some shit came up yesterday... If you message me I'll keep you updated. Title: Re: help with rear 02's mk4 r32( have some locations already) Post by: J.Laborde on July 31, 2018, 12:33:31 AM Hello :) ,
Attached is your R32_EG file with the entire Project Konfiguration table defined in an OLS, compatible with WinOLS 2.24/2.26. I can give you an entire map pack in english specially designed for Stage 1/ Stage 2 tuning if you're happy to pay for it. ~J.Laborde Title: Re: help with rear 02's mk4 r32( have some locations already) Post by: vwdubNam on July 31, 2018, 03:29:30 AM Hello :) , i'll in box you. i realkly just need thatAttached is your R32_EG file with the entire Project Konfiguration table defined in an OLS, compatible with WinOLS 2.24/2.26. I can give you an entire map pack in english specially designed for Stage 1/ Stage 2 tuning if you're happy to pay for it. ~J.Laborde Title: Re: help with rear 02's mk4 r32( have some locations already) Post by: up50lut3 on August 07, 2018, 09:56:12 AM Hello :) , Attached is your R32_EG file with the entire Project Konfiguration table defined in an OLS, compatible with WinOLS 2.24/2.26. I can give you an entire map pack in english specially designed for Stage 1/ Stage 2 tuning if you're happy to pay for it. ~J.Laborde thank you! |