NefMoto

Hi guy's! I'm new here and i'm interested of ECU tuning(EDC15 on a Skoda Octavia 1 ASZ engine) for a little more power (stage 1) and h low fuel consumption. I've try modify my stock map with EDC Suite after I follow some YouTube tutorials (torque limiter, driver wish, smoke limiter, target boost) but i don't understanding what value must be change and how. I use MPPS 13 for reading and writing maps on my car.
Can somebody explain me what maps must be modify ( for my PD130 ps ) and how for obtaining more power and torque at a low fuel consumption?

Cheers, guy's !

It's a simple concept. Add more boost and fuel. When you're playing with torque limiter, smoke limiter, and driver wish what are you modifying in those maps? Mg per stroke right? Well you're allowing more fuel to be injected. Boost limiter and target boost are obviously tables. N75 is duty cycle % table to reach requested boost. Stop expecting a handout and make some changes flash your car and log. You have about the easiest car to tune including the luxury of a full tuing suite someone made for free. Really it couldn't be easier

Very simply ecu to tune. I can give You some adresses...

51D48 - Boost Limiter
71D48 - Boost Limiter
573CE - Boost Limiter Map
773CE - Boost Limiter Map
4D244 - Driver Wish
6D244 - Driver Wish
547DE - Duration Map
54A64 - Duration Map
54CEA - Duration Map
54F70 - Duration Map
747DE - Duration Map
74A64 - Duration Map
74CEA - Duration Map
74F70 - Duration Map
4C116 - EGR Map
6C116 - EGR Map
546D0 - Fuel Map
56FAC - N75 Map
76FAC - N75 Map
4DCCE - Smoke Limiter by MAF
6DCCE - Smoke Limiter by MAF
4D956 - Torque Limiter
6D956 - Torque Limiter
56CA0 - Turbo Map
76CA0 - Turbo Map

Remember to calculate checksums! MPPS dont correct CS. MPPS cant check checksums (module can say that all CS is ok but CS in reality is not ok...)

MŚ.

What do you think about this map? I tried to change myself (driver wish, torque limiter, smoke limiter, IQ MAF limiter, IQ MAP limiter, BOOST target, BOOST presure limiter).
Do you think i have modify correcty the maps for more power and torque at a low consumption?
What maps must be change for stage 1 in safe mode (my car is stock, except 60mm inch half exhaust)?

All the best!

In my opinion
-TQ is too high. I prefere add to whole table.. anyway You should't set more than 65-66mg or maybe You like black smoke..
-IQ by MAF (Smoke limiter) not changed
-Durations not touched?
-Reqesting too much boost at low rpms  :o  Added extra boost to whole table  ???
-EOI/SOI?
-EGR not disabled
-N75 must be touched to get better boost response and hold... and for economy changes
-Boost in lower IQ i setting lower to do lower load. Is good for economy.
-Your flash have 3 sectors (dpp addreses)... i dont know what map working now and you if you dont know it You must change all 3 locations.

I made file for You quickly. Thanks rep please.

MŚ.

Thanks for rapid reply  ;D
I will try to put your map on car later and i will notify you   :)
Thank you so much for your time and work!

Cheers! :-*

I tried two days ago to activate launch control and popcorn limiter. Launch control work very good, but the popcorn limiter (at 4200 made with SVRL, modified at adress 5xxxx 6xxxx and 7xxxx) sound like popcorn, but the car is flattening at this rpm

I think i was wrong..
I will upload the map with launch control and popcorn limiter morning, and i will wait your opinions  ;D

My respect for all!

I don't remember but this can work in this ecu. Try this. SVRL set to stock value.

Good morning guy's!
I tried to do launch control (2600rpm - 2700rpm) and popcorn limiter (4200rpm) in EDC suite :D
What do you think about?  ::)

I finished for myself ecu file for my Skoda Octavia ASZ engine
What do you think about ?