|
Title: ecu cloning Post by: nmd on February 04, 2019, 03:21:37 AM Hi
I found some info but not all so that's why I asking! Was trying to put in another ecu in my car. Would like to have my original ecu in case of a misshapps. I have me7.5 ecu bosch nr 0261208500. And when I changed the ecu and car would not start..due to immo. Spare and org ecu have the same boschnumber. But i have used nefmoto software to get a bin file on my original ecu over obd2. But is there any difference if i get a bin file with obd2 or on a bench in boot-mode with a galletto (Chinese knockoff)? Is there any differences.. Will I get the same info from bench flash or over obd2? When in bootmode on the spare ecu. To flash my original bin file. Will that overwrite the immo protection so that it would be a perfect clone. And I could have some fun and test different setting without be afraid to brick my original ecu. I do this because i would like to skip the step with vcds to adopt the ecu. The car is Audi A4 avant quatto 1.8ts -04 ...B6 Title: Re: ecu cloning Post by: adam- on February 04, 2019, 05:20:21 AM EEPROM needs read, not flash.
Title: Re: ecu cloning Post by: nmd on February 04, 2019, 06:32:02 AM aha.... now I get it... Thanks!!
One word can help so much .... Thanks! Title: Re: ecu cloning Post by: nmd on February 05, 2019, 05:59:03 AM Tested the me7eeprom v1.40 and 1.31 and got some errors.. I have a dumb generic kkl cable... will order a galletto knockoff but it take 1½week to get it.
This was over the ODB read. But it fails.... Errors are : Me7-eeprom>ME7EEPROM.exe --OBD -r -p 3 audi.bin ME7_EEPROM v1.40 COM: 3, Baud Rate: 10400 Opening COM3 ... OK Initiating communication ... FAIL. (error=0x50101) Closing COM3 Me7-eeprom>ME7_95040.exe --OBD -r -p 3 audi.bin Ver: 1.31 Com Port: 3 Baud Rate: 10400 Opening COM3 ... OK Initiating communication ... FAIL. (error=0x01) Closing COM3 I must write it in bootmode on spare ecu so maybe I should try to read in bootmode to. Title: Re: ecu cloning Post by: aef on February 06, 2019, 01:16:43 AM --OBD will not work from my experience
This whole topic is useless if you would have started by reading the stickies and existing threads about cloning, me7eeprom tool and so on Title: Re: ecu cloning Post by: dilly on February 08, 2019, 04:25:10 PM --OBD will not work from my experience you are correct This whole topic is useless if you would have started by reading the stickies and existing threads about cloning, me7eeprom tool and so on you cannot write the eeprom via obd you can only read it reading by --OBD is a hit or miss best bet is to read and write via bootmode Title: Re: ecu cloning Post by: adam- on February 09, 2019, 04:00:23 AM Noticed this too. Not sure if a bug, but it used to work great and now it doesn't. Weird.
Title: Re: ecu cloning Post by: nmd on February 15, 2019, 12:05:18 PM Having some trouble getting my spare ecu in bootmode. Does this ecu req 10kohm solution is this 1k ohm solution????
Title: Re: ecu cloning Post by: aef on February 15, 2019, 12:38:34 PM ecu number is a secret ::)
Title: Re: ecu cloning Post by: nmd on February 15, 2019, 01:14:39 PM Sorry... Hoped the bosch number would be sufficient.
But vag number is 8E0909518AS. Title: Re: ecu cloning Post by: nmd on February 16, 2019, 09:05:40 AM Croped the original photo. Here you can see the numbers on the cpu
Title: Re: ecu cloning Post by: SQT on February 17, 2019, 10:51:32 PM Croped the original photo. Here you can see the numbers on the cpu hi guy, use "eeprom tools" from the set of VisualME7_Logger to transfer immo data and wines numbers from your unit to the one you boughtTitle: Re: ecu cloning Post by: SQT on February 17, 2019, 10:54:21 PM Having some trouble getting my spare ecu in bootmode. Does this ecu req 10kohm solution is this 1k ohm solution???? Are you using a resistor to close the contact to ground? In this case, if I'm not mistaken no difference at 10 kOhm or 1kOhmTitle: Re: ecu cloning Post by: SQT on February 17, 2019, 11:03:30 PM --OBD will not work from my experience totally agree with youThis whole topic is useless if you would have started by reading the stickies and existing threads about cloning, me7eeprom tool and so on |