|
Title: mpps EDC17c10 and k-line! Post by: beou on September 12, 2020, 06:48:06 AM Hello!!
Newbie here trying to flash my own citroen c3! I have an EDC17c10, (lid opened and ready for boot mode) When i am trying to ECU id or read, the mpps v18 prompts this: 'Please make sure that KLINE is connected to the ignition pin' As i know, flashing an EDC17c10 with mpps does not require the k-line cable! Just CAN-H and CAN-L! Do i have to use K line cable too? Thanks! Title: Re: Re: mpps EDC17c10 and k-line! Post by: xXxCryxXx on September 12, 2020, 06:54:22 AM Hello!! Clone?Newbie here trying to flash my own citroen c3! I have an EDC17c10, (lid opened and ready for boot mode) When i am trying to ECU id or read, the mpps v18 prompts this: 'Please make sure that KLINE is connected to the ignition pin' As i know, flashing an EDC17c10 with mpps does not require the k-line cable! Just CAN-H and CAN-L! Do i have to use K line cable too? Thanks! X-Boost Performance Title: Re: mpps EDC17c10 and k-line! Post by: beou on September 12, 2020, 07:06:23 AM Its a clone yes!!
Title: Re: Re: mpps EDC17c10 and k-line! Post by: xXxCryxXx on September 12, 2020, 07:08:19 AM Its a clone yes!! Make a second green kabel on the main green kabel for ignition X-Boost Performance Title: Re: Re: Re: mpps EDC17c10 and k-line! Post by: xXxCryxXx on September 12, 2020, 07:10:40 AM Make a second green kabel on the main green kabel for ignition and Picture of wiring please X-Boost Performance X-Boost Performance Title: Re: mpps EDC17c10 and k-line! Post by: beou on September 12, 2020, 07:19:32 AM Thanks for your reply!
EDC17c10 needs ground at pin 4, 12v at pin 2, and 12v too at pin 19! Pin 19 is the ignition pin i assume! CAN-H at pin 40 and CAN-L at pin 52! In the mpps breakout cable, the CAN-H is the blue wire! The CAN-L is the orange one! K-line is green! Why do i need two K-line cables? In the photo, CAN-H and CAN-L are marked with different colours but i think that it doesnt matter! Title: Re: Re: mpps EDC17c10 and k-line! Post by: xXxCryxXx on September 12, 2020, 07:21:24 AM Thanks for your reply! Do you have connected pin 9 and 12? EDC17c10 needs ground at pin 4, 12v at pin 2, and 12v too at pin 19! Pin 19 is the ignition pin i assume! CAN-H at pin 40 and CAN-L at pin 52! In the mpps breakout cable, the CAN-H is the blue wire! The CAN-L is the orange one! K-line is green! Why do i need two K-line cables? In the photo, CAN-H and CAN-L are marked with different colours but i think that it doesnt matter! X-Boost Performance Title: Re: mpps EDC17c10 and k-line! Post by: xXxCryxXx on September 12, 2020, 07:22:52 AM Sorry wrong text Where is the Pin Out of your seller for the mmps flasher?
X-Boost Performance Title: Re: mpps EDC17c10 and k-line! Post by: beou on September 12, 2020, 07:35:41 AM Seller didnt provided any pinout!
I did a research and i think that the colors are correct! I can confirm the the BLUE cable is CAN-H and ORANGE is CAN-L! Used a multimeter and checked that the BLUE goes straight at pin 7 of the a1050c CAN transeiver chip! So is the ORANGE connected straigth to pin 6 of the same chip. Title: Re: Re: mpps EDC17c10 and k-line! Post by: xXxCryxXx on September 12, 2020, 07:37:07 AM Seller didnt provided any pinout! Wait i will later look at my KTag the Pinout for Bootmode right? it sould be the sameI did a research and i think that the colors are correct! I can confirm the the BLUE cable is CAN-H and ORANGE is CAN-L! Used a multimeter and checked that the BLUE goes straight at pin 7 of the a1050c CAN transeiver chip! So is the ORANGE connected straigth to pin 6 of the same chip. X-Boost Performance Title: Re: mpps EDC17c10 and k-line! Post by: beou on September 12, 2020, 07:42:19 AM Thanks in advance for your effort!
I think that Ktag has different colors! Title: Re: Re: mpps EDC17c10 and k-line! Post by: xXxCryxXx on September 12, 2020, 09:46:04 AM Thanks in advance for your effort! no i dont Think so... you need Bootpin too....(https://uploads.tapatalk-cdn.com/20200912/7de7d67bf02645ca1dd7ce96c17b1a29.jpg)(https://uploads.tapatalk-cdn.com/20200912/200bcb978703512911cc65f12664bdac.jpg)(https://uploads.tapatalk-cdn.com/20200912/4daaafa3dbbab70d3966261b6ece669e.jpg)I think that Ktag has different colors! X-Boost Performance Title: Re: mpps EDC17c10 and k-line! Post by: beou on September 12, 2020, 10:07:43 AM Thanks again!! I have already soldered a boot pin wire from the begining!
But the result is the same! :-\ Title: Re: Re: mpps EDC17c10 and k-line! Post by: xXxCryxXx on September 12, 2020, 10:18:55 AM Thanks again!! I have already soldered a boot pin wire from the begining! Maybe the Protocol of Clone MPPS is wrong .... that happens becuse Clone sorry M8 ... But the result is the same! :-\ Title: Re: mpps EDC17c10 and k-line! Post by: beou on September 12, 2020, 10:27:04 AM OK! I will keep trying!
Thanks a lot for your help man!! Cheers Title: Re: Re: mpps EDC17c10 and k-line! Post by: nyet on September 12, 2020, 11:30:07 AM no i dont Think so... you need Bootpin too....(https://uploads.tapatalk-cdn.com/20200912/7de7d67bf02645ca1dd7ce96c17b1a29.jpg)(https://uploads.tapatalk-cdn.com/20200912/200bcb978703512911cc65f12664bdac.jpg)(https://uploads.tapatalk-cdn.com/20200912/4daaafa3dbbab70d3966261b6ece669e.jpg) X-Boost Performance Can you take a real screen shot and not take pictures with your phone? Or post the original images. Thanks. Pictures of a screen are really pretty awful |