|
Title: Galletto - boot mode only? Post by: Rick on September 15, 2010, 02:07:12 AM as above, can our ECU's be read only using boot mode with galletto?
What's needed to make a bench harness? A female port for the galletto and a plug for the ECU? Rick Title: Re: Galletto - boot mode only? Post by: Tony@NefMoto on September 15, 2010, 01:57:54 PM I have only been able to read the ME7 using Galletto in boot mode.
To make a bench harness you need to connect the K-line, ground, power, and ignition lines between the OBD plug of the cable and the ECU. Then you need to provide 12v and ground. Title: Re: Galletto - boot mode only? Post by: AndiS4 on July 10, 2012, 02:45:46 PM Isnt it even possible to flash in car without boot mode with the 1260-Galletto?
Title: Re: Galletto - boot mode only? Post by: nyet on July 10, 2012, 03:49:51 PM No.
Title: Re: Galletto - boot mode only? Post by: littco on July 10, 2012, 04:15:55 PM Not sure I agree here, either that or I don't follow the questions.
I can read with galletto in the car, recently read an Audi s3 2000. Also know it works on an A3 AUQ and Audi TT apx 2001,and my old S3 1999 APY read as well. they are all Me7 ecu's. I also flash in car on my current S3 in normal mode. Title: Re: Galletto - boot mode only? Post by: k0mpresd on July 10, 2012, 06:14:23 PM yep, ive read and flashed before, no issues.
Title: Re: Galletto - boot mode only? Post by: cactusgreens4 on July 10, 2012, 07:05:23 PM am i hearing that you can read and flash with galetto not in boot mode?
Title: Re: Galletto - boot mode only? Post by: k0mpresd on July 10, 2012, 07:45:47 PM you can. but i never did it. i always use bootmode pretty much no matter what. i always feel its a safer flash.
Title: Re: Galletto - boot mode only? Post by: littco on July 10, 2012, 11:37:55 PM am i hearing that you can read and flash with galetto not in boot mode? Yep read takes about 90 seconds, flash takes 240 seconds. And it was the only cable I found to work on my edc15 ecu on my golf. Title: Re: Galletto - boot mode only? Post by: AndiS4 on July 11, 2012, 01:32:46 AM Yep read takes about 90 seconds, flash takes 240 seconds. Does it work only on your edc, or also on ME7.1 (e.g. S4).. I have been told from a friend, that its no problem to flash with galletto1260 via obd. I think I will give it a try this evening... Then we will be sure :) I hope it doesnt brake or brick anything... Title: Re: Galletto - boot mode only? Post by: littco on July 11, 2012, 01:46:28 AM Currently it works on my me7.5 s3 ban , me7.1 s3 apy and also edc15p but I know it doesn't work on my Audi a4 me7.5 bfb 2004, but then neither does nefmoto software! I'm think it's a cluster issue that stops it as on bench even in normal mode it reads fine!
Title: Re: Galletto - boot mode only? Post by: nyet on July 11, 2012, 10:12:27 AM Sorry, i wasn't clear.
for ME7.1, bootmode only. no clue about other ECUs Title: Re: Galletto - boot mode only? Post by: AndiS4 on July 11, 2012, 12:22:11 PM Hmm, ,Ive been told, it should be running fine on the me7.1 aswell...
But I cant confirm it, because my galletto seems to be corrupt... Yesterday it was able to read out ecu data (didnt try read or flash flash memory). Today nothing works... perhaps its because its an ebay-one... If there is success, ill post it.. But for today ill quit trying to find out.. Title: Re: Galletto - boot mode only? Post by: AndiS4 on July 13, 2012, 01:41:38 AM Hmm,
didnt get it to work again. Galletto hangs up every time i try work with it. Even using another computer didnt help. Seems as if the cable is defective. Title: Re: Galletto - boot mode only? Post by: AndiS4 on July 13, 2012, 01:24:34 PM OK! Good News! IT WORKS!
The cable was ok. The problem was the voltage. I wanted to work with 13V and more. Obvisiously, the cheap Galletto doesnt work with that voltage, although a voltage like that is demanded .!!! So 12.X Volts are better for working than 13+! So all in all, i can say Galletto 1260 works on an S4 ME7.1 (29f800bb) via OBD onboard flash without boot mode! The flash needed about 22 minutes. Have fun! Title: Re: Galletto - boot mode only? Post by: phila_dot on July 13, 2012, 02:39:42 PM OK! Good News! IT WORKS! The cable was ok. The problem was the voltage. I wanted to work with 13V and more. Obvisiously, the cheap Galletto doesnt work with that voltage, although a voltage like that is demanded .!!! So 12.X Volts are better for working than 13+! So all in all, i can say Galletto 1260 works on an S4 ME7.1 (29f800bb) via OBD onboard flash without boot mode! The flash needed about 22 minutes. Have fun! Why? Why not use NefMoto? Title: Re: Galletto - boot mode only? Post by: AndiS4 on July 13, 2012, 03:02:13 PM I think its just a thing good to know...
Because most think galletto is only Working in boot mode on s4's me7.1... I just wanted to find out. Now i can confirm it runs.:) Title: Re: Galletto - boot mode only? Post by: phila_dot on July 13, 2012, 03:11:26 PM I think its just a thing good to know... Because most think galletto is only Working in boot mode on s4's me7.1... I just wanted to find out. Now i can confirm it runs.:) Galletto is only useful in boot mode for recovery. 1 min to flash with Nef > 22 mins to flash with Galletto. Title: Re: Galletto - boot mode only? Post by: AndiS4 on July 13, 2012, 03:14:52 PM Ill try it the next flash. :)
|