|
Title: Corrupt EEPROM? Programming Not Finished P1681 Had leaky capacitors Post by: mdccode5150 on October 30, 2020, 05:39:20 PM I purchased a 2003 Audi TT 180HP for MOM. It had a blown head gasket. I got that fixed and the vacuum lines, but now it has a check engine light and the code below. I re-flashed a known good file that also reads 100% same as mine, and didn't fix it. So I purchased a new used ECM/ECU and put one of the top virgin eeprom's (ddillenger's) on it...it runs and no check engine. I tried to adapt it with VCDS and no go. I then checked it with eepromtool_04.exe (see below) and noticed it's a IMMO2, and mines an immo3. Can someone help with checking or fixing my EEPROM? or modifying a virgin with my information? Thanks
1 Fault Found 18089 - Control Module Programming Not Finished P1681 - 35-00 - C:\>eepromtool_04.exe ori.bin Read in 512bytes EEPROM Status: - Type: ECU_eeprom - Version: Immo2 - VIN: XXXXXXXXXXXXXXXXX - SKC: 065535 - Immobiliser: Error, set Immo - Current values: 0x12 = 0x04, 0x22 = 0x04 - Checksum: OK - Size: 512bytes - Cluster Code: 00 00 00 00 00 00 00 - P0601 DTC: not set - Immo ID: XXXXXXXXXXXXXX - Softcoding ID: 10710 - Tuner Tag: - Flash Programming (successful): 0 - Flash Programming (attempts): 0 C:\>' C:\>eepromtool_04 ori.bin Read in 512bytes EEPROM Status: - Type: ECU_eeprom - Version: Immo3 - VIN: TRUSC28N951004261 (Audi Hungary 2005 - TT 99-06, Gyor, Hungary) - SKC: 02990 - Immobiliser: On - Checksum: OK - Size: 512bytes - Cluster Code: 14 22 3A 5E 7C 9A B7 - P0601 DTC: not set - Immo ID: AUZ5Z0D5076008 - Softcoding ID: 7570 - Tuner Tag: - Flash Programming (successful): 1 - Flash Programming (attempts): 0 C:\> Title: Re: Corrupt EEPROM? Programming Not Finished P1681 Had leaky capacitors Post by: mdccode5150 on November 01, 2020, 10:31:05 PM Read these
http://nefariousmotorsports.com/forum/index.php?topic=3928.0title= http://nefariousmotorsports.com/forum/index.php?topic=1845.msg17936#msg17936 Tried this http://nefariousmotorsports.com/forum/index.php?topic=6719.0 Going to read this http://nefariousmotorsports.com/forum/index.php?topic=2200.msg65208#msg65208 Thought I was getting somewhere but code came back and after that lost ground so I went back to original EEPROM, and EPROM. PS I have tried MPPS 13, and 18 Galletto in boot mode. Title: Re: Corrupt EEPROM? Programming Not Finished P1681 Had leaky capacitors Post by: mdccode5150 on November 02, 2020, 12:34:24 AM Problem solved did everything (change 2D 0D) over with the new ecm/ecu then checksummed it with MPPS V16, and that worked (for the new one), but the old one had to be bootmode and now it works (it's a little slow on the uptake, but good for emergencies).
Also WinOLS failed to catch the checksums (2) |