NefMoto

Hello is there relation between gearbox sw and load request in D, Tip , S  modes . Because on Direct ecu does not open throttle at 100% but pedal is pressed to the floor till 4k rpm ? Mode S makes ecu open it at 100% from 1500-2000  or there is something in Rom that controls this thing ? Sorry if im not at right section let moderator move it to noob questions .
Engine 2.7t / chasis a6 4F/ Geabox 6hp19a sw 551R . 

logs.

Here they are on D. Tested this night again but not logged im wrong with S mode still wont open but its completely diferent car. I think its ecu software related because i keep it stock as much as i can i dont have hardawe to support tune for now .  Delete post if u decide

Perhaps it is just torque intervention from the gearbox due to limiters inside TCU.

So there is chance tcu to cut throtle. Because im the beggining of me 7.x tune learning . Gearbox is from 3.2FSI with flash for 3.0 Mpi BBJ/ASN like motor . Thank you :)

This might be helpful. Dig around in the FR a bit, there is TCU induced torque intervention

https://s4wiki.com/wiki/Tuning#Disable_ASR

Unfortunately you should only use it to check if that is the reason. Otherwise you risk destroying your transmission. If it is really because of TCU you should tune TCU so it will cope with higher torque!!!

This.

Understand. I dont care about gearbox i think 3.0TFSI uses same . Thank you boys im going to read and practice .

You would be looking for something like this in the 7.1.1 maps if it is there.. this is off the A6 4F 3.0t with 6hp19 with simos engine ecu.
I would like to see some pictures of the 2.7t in the 4f chassis if you have any.

Why would you suggest that KFPED might be connected to that issue?

Correct, KFPED has nothing to do with TCU induced ASR.

Sorry if I am wrong, Its how I interpreted his original first post asking if there was any maps in the engine ecu that control throttle.

If you share your ROM with me i can look to see you didnt miss any limiters. PM me if needed.

i have a lot of pics but doez not allow me to upload it  its too big.
Tried asr msr off with no sucsess. What file do u need ecu Rom or gearbox , because i can upload only ECU . Rom from gearbox i dont have nothing to dump it in bin format . Im flashing it only with VASPc with SGO file Gearbox is from 3.2 FSI simos controlled i uploaded 3.0 MPI BBJ Sgo and marty and prj told me to correct canvers fmotc cwgc , i have tried flashing it back to 3.2  softwaere with corrected parameters to match but with no sucsess , Tried 4.2 BAT 7.1.1 controlled still no sucsess  Tried Nm matching in ECU bin still no sucsess.

Here is image to understand what i mean . I will resise pics and upload engine bay .

dude wtf why aren't you using export or at least screen shot.

Don't resize, just don't take fucking potato phone pictures with your phone.

File->Export

it isn't hard.

Not only that, but you should be attaching a log.

Sorry i dont have pc in my hands its pic in phone. Log attached to first 2 replays same as pic. I forgot to tell that i dont have working abs after 20 kmh disables esp abs asr whatever can control brakes, because bad speed sensor on front right wheel. Also i think to match these maps to fit this gearbox ,because its a lot longer with different final drive of 3.1/1 i think
NVQUOT1O
NVQUOT1U
NVQUOT2O
NVQUOT2U
NVQUOT3O
NVQUOT3U
NVQUOT4O
NVQUOT4U
NVQUOT5O
NVQUOT5U
NVQUOT6O
NVQUOT6U

You need to revise your workflow. Tuning requires an attention to detail you seem to be avoiding.

understand , it will not repeat. Sorry again

Hi, is 6HP19 successful?

15K km no issues its a bit laggy and a lot of power cut till 3k but on S mode no issues for now .

Hello!can you tell us about the nuances of installing 6hp with a 7.1.1 block?