|
Title: R32T Mono Lambda Patch Post by: Praga on March 02, 2021, 04:56:43 AM Hello
I hope everyone is well. Have a R32 Turbo with dual lambdas installed after the turbos (in a single pipe). I looked at several posts on the forum and made changes to the MPC file. I think the mono lambda patch is working now. Please see attached logs. The first and second lambda correction is similar. Can anyone confirm is this is the way it should be ? Praga Title: Re: R32T Mono Lambda Patch Post by: prj on March 02, 2021, 02:34:56 PM No one who knows what they are doing is going to waste their time going through a file and your log does not show trims.
What you need to do from memory is copy: fr_w -> fr2_w frm_w -> frm2_w rkaz_w -> rkaz2_w rkat_w -> rkat2_w frau_w -> frau2_w fra_w -> fra2_w frao_w -> frao2_w If you want to be extra complete you can also copy the voltage by making both read the same ADC. Find where they are assigned, and instead of assigning them from calculation load the variable and copy it. If you don't do all the fuel trims, you can have an issue with runaway trim on a bank and fault codes. If you don't care about that and know how to disable it, you can copy rk_w -> rk2_w IIRC, but bank 2 fuel trims will show stupid values and throw codes. Title: Re: R32T Mono Lambda Patch Post by: Praga on March 03, 2021, 12:19:55 AM No one who knows what they are doing is going to waste their time going through a file and your log does not show trims. What you need to do from memory is copy: fr_w -> fr2_w frm_w -> frm2_w rkaz_w -> rkaz2_w rkat_w -> rkat2_w frau_w -> frau2_w fra_w -> fra2_w frao_w -> frao2_w If you want to be extra complete you can also copy the voltage by making both read the same ADC. Find where they are assigned, and instead of assigning them from calculation load the variable and copy it. If you don't do all the fuel trims, you can have an issue with runaway trim on a bank and fault codes. If you don't care about that and know how to disable it, you can copy rk_w -> rk2_w IIRC, but bank 2 fuel trims will show stupid values and throw codes. Thank you PRJ Title: Re: R32T Mono Lambda Patch Post by: fknbrkn on January 15, 2023, 01:22:22 AM im stuck a bit with the st10 022906032KR ecu and mono lambda
Copied adc input from bank1 to bank2 All from prjs list also was transferred (except rk_w) While its working like a charm on a 2.7t here we get troubles with actual lambda goes lean, fr_w tried to catch this and so on with floating mixture Unfortunately im far far away from the car and only vcds logs available, ill post it later Second problem with the HSH, in 2.7t i just feeded bank2 heizung voltage with bank1 and everything was fine but i cant find same on wideband Title: Re: R32T Mono Lambda Patch Post by: prj on January 15, 2023, 04:59:54 AM It means you did not copy some fuel trim correctly or made a mistake somewhere.
I've done many ST10 with this method. Title: Re: R32T Mono Lambda Patch Post by: fknbrkn on January 16, 2023, 01:34:38 AM Code: ROM:000A73B0 E6 FC 00 80 mov r12, #8000h Same with fra* and rka* Ill try to replace rk_w to be sure Title: Re: R32T Mono Lambda Patch Post by: prj on January 16, 2023, 06:14:31 PM I usually never replace rk.
You sure this is only problem with car? ;) I've just done so many of these, ST10 and C167, and I've never ever had a single problem by just copying all the fuel trims over and the ADC. Title: Re: R32T Mono Lambda Patch Post by: fknbrkn on January 31, 2023, 02:03:13 AM Well only rk_w replacement (no other changes in code) gives the same result - fr_w/2 starts to fluctuate so the afr is
We have also tried to log with vehical, it connects.. checks baudrates and throw "ERROR: unable to detect baud rate" Problem appears only when b2 copied from b1. It works fine with stock MPC where only b1 LR active In attachment logs with rk_w only patch And here is the link to logs with the stock code wo any patches where only bank1 is active (there is no MAF connected but its irrelevant in that case) Found your advice but cannot find any DDKA / DMEA in FR Quote If you're running single bank (which btw isn't the best idea on VR6 due to the two banks being fed differently, there is a massive richness offset on DDKA and DMEA for example from stock, to not grenade half the engine), then you need another patch for single lambda, but that isn't that hard either. I believe its some kind of Diagnose Kraftoftsysteme or so but unable to find something similar Also i didnt find any offset to b2 in GK .. there is difference in PID regelung and also KFDLASO1/2 but its some kind a lambdasoll correction Anyway im out of ideas.. Title: Re: R32T Mono Lambda Patch Post by: prj on January 31, 2023, 03:42:47 AM My logger does not support ST10 at all.
And I have no idea, I've done quite a few ST10 and did not have this problem, maybe it's a newer software. Title: Re: R32T Mono Lambda Patch Post by: R32Dude on January 31, 2023, 06:46:44 AM Try the R32logger, you will need RAM addresses though.
Title: Re: R32T Mono Lambda Patch Post by: fknbrkn on February 01, 2023, 12:01:40 AM Try the R32logger, you will need RAM addresses though. Thx ill check it So far so good Lowering lambda P and I by 15% give us good result and oscillations almost gone at idle Title: Re: R32T Mono Lambda Patch Post by: fknbrkn on February 04, 2023, 11:12:57 AM Thx ill check it So far so good Lowering lambda P and I by 15% give us good result and oscillations almost gone at idle Nvm after few revs to 3k its goes wild at idle The engine is modified 2.8 with 3.2 ecu, i fixed ve, cam things etc but seems its over complicated for me Title: Re: R32T Mono Lambda Patch Post by: _nameless on February 04, 2023, 01:11:50 PM Nvm after few revs to 3k its goes wild at idle Why not use the usdm 2.8 24v single lambda file?The engine is modified 2.8 with 3.2 ecu, i fixed ve, cam things etc but seems its over complicated for me Title: Re: R32T Mono Lambda Patch Post by: fknbrkn on February 11, 2023, 08:08:28 AM Why not use the usdm 2.8 24v single lambda file? Its dsg equipped unfortunally Title: Re: R32T Mono Lambda Patch Post by: IamwhoIam on February 11, 2023, 08:56:19 AM Its dsg equipped unfortunally I'm sure that file can be made to run with a DSG Title: Re: R32T Mono Lambda Patch Post by: _nameless on February 11, 2023, 09:29:47 AM Its dsg equipped unfortunally They had auto 24v cars too |