|
Title: Anyone ever used the free ST10 flasher tool? Post by: R32Dude on June 25, 2021, 06:26:34 AM I'm trying to dump the mpc from my ecu using the mentioned tool V2.4. I haven't played too much as I don't want to brick it but when I tried dumping all the blocks it gave an error message. I got scared and didn't try again after that. Luckily the ecu is fine.
Would anyone with experience know if it would work if I dump just the first block of 32K and then skip blocks up to 0x18000 and dump all the rest after that? Title: Re: Anyone ever used the free ST10 flasher tool? Post by: R32Dude on June 28, 2021, 03:40:10 AM Problem solved.
St10 flasher 2.4b has a problem writing to a hex file but writes a txt file flawlessly. I wrote a simple program to convert it to binary. Got the whole 832KB out of the st10f276. Good for a free tool. I wasn't game enough to try the clone mpps V12/13 as it bricked the ecu in bootmode when it gave an error erasing the flash. Galletto fixed it. Title: Re: Anyone ever used the free ST10 flasher tool? Post by: eNDi on April 29, 2022, 04:10:16 AM I have the same problem with ST10 Flasher Tool 2.4b (tool v2.3c, dll 2.4b) - a HEX dump gives error "LoadExternalFlashMonitor: target Not found". It's seems to be a problem with the st10flasher.dll: older versions of the flasher tool can write HEX dump - e.g. 2.02 (tool v2.02a, dll 2.02b) or 2.3g (tool v2.3c, dll 2.3g).
Title: Re: Anyone ever used the free ST10 flasher tool? Post by: R32Dude on April 29, 2022, 04:45:27 AM I use MPPS v13 nowadays. It was cheap but does the trick.
Title: Re: Anyone ever used the free ST10 flasher tool? Post by: voltprinter on May 29, 2022, 11:59:17 AM Problem solved. St10 flasher 2.4b has a problem writing to a hex file but writes a txt file flawlessly. I wrote a simple program to convert it to binary. Got the whole 832KB out of the st10f276. Good for a free tool. I wasn't game enough to try the clone mpps V12/13 as it bricked the ecu in bootmode when it gave an error erasing the flash. Galletto fixed it. I've been searching all over what to do with a 832kb file and cannot find the answer. I have a ME7.1.1 Type 3, was able to get it into bootmode with a resistor on pin 24. I used MPPS v18 to do the dump, but no ME7 tools are happy with its outputs. I'm not sure what to do now. Title: Re: Anyone ever used the free ST10 flasher tool? Post by: R32Dude on May 29, 2022, 06:33:58 PM Not sure what you are asking, but the 1024 kB flash has the maps most people tune. The 832kB is mostly code and no software I have seen around deals directly with it. You use IDA to alter it.
Title: Re: Anyone ever used the free ST10 flasher tool? Post by: bamofo on June 15, 2022, 08:16:07 AM Not sure what you are asking, but the 1024 kB flash has the maps most people tune. The 832kB is mostly code and no software I have seen around deals directly with it. You use IDA to alter it. Pop and bangs is in the 832kb file ;-) Title: Re: Anyone ever used the free ST10 flasher tool? Post by: _nameless on June 22, 2022, 10:14:46 PM Pop and bangs is in the 832kb file ;-) :D :D :D :D |