|
Title: Martys map list for pops and bangs m3.8.3 and m5.9.2 Post by: _nameless on July 22, 2021, 07:43:26 PM DNSLL.0
DNSLL.1 NWEM.0 NWEM.1 TLSN.0 TVSAM.0 TVSAM.1 KFWLL.0 ** This one threw me for a loop. translated as idle ignition during warmup, but i found that it always returns to this table for idle and overrun after about 4 hours of logging i figured it out. Also, may be worth noting the last axis value is 3k rpm i changed it to 7k and it helped with the switchover time delay KFZWMN **KFZWOPT.0 I didnt test with this map but it may help. Title: Re: Martys map list for pops and bangs m3.8.3 and m5.9.2 Post by: ZpiXDK on July 28, 2021, 03:30:35 AM Can you confirm that TLSN is 0 on M3.8.3? (on 3.8.1/3.8.2 it's not)
In the Damos I have for M3.8.3 it dosn't have TLSN and TVSAM, but the 3 maps is just before TVSSGM (4x1)? EDIT: It was those maps Also what does TL stand for? EDIT: Are you able to get fast pops? it will not pop right away, first after 1-2 sec. and only 1-2 pops -TVSAM - Tried to lower and increase, but not really seeing much different, it might pop even later when I increase it -TLSN? - how much load you set here? I set it to 4? (So under 4ms load it wil enable overrun?) -KFWLL - I have axis 800, 1000, 1480, 2000, 3520, 5000 and 7000 -KFZWOPT - set to match KFWLL in the ATDC area -DTLWE - We don't need this? (Hysterses for TLSN I guess) Title: Re: Martys map list for pops and bangs m3.8.3 and m5.9.2 Post by: marantzvieta on August 07, 2024, 11:00:40 AM Mate, sorry to bother you and retrieve an old post. Could you please confirm this maps did work on m3.8.3? I have transfered my values from this maps from M3.8.2 (where it worked) to m3.8.3, and I still feel the engine cutting as soon as I release the throttle, no matter what values I insert in TVSAM.0 and TVSAM.1
As I mentioned, M3.8.2 works as expected and takes longer to "cut" the engine, as expected bc of values in TVSAM maps... Thanks for your input. Best regards, DNSLL.0 DNSLL.1 NWEM.0 NWEM.1 TLSN.0 TVSAM.0 TVSAM.1 KFWLL.0 ** This one threw me for a loop. translated as idle ignition during warmup, but i found that it always returns to this table for idle and overrun after about 4 hours of logging i figured it out. Also, may be worth noting the last axis value is 3k rpm i changed it to 7k and it helped with the switchover time delay KFZWMN **KFZWOPT.0 I didnt test with this map but it may help. Title: Re: Martys map list for pops and bangs m3.8.3 and m5.9.2 Post by: marantzvieta on August 07, 2024, 01:40:20 PM I CANNOT belive this f****** ecu. TVSAM.0 TVSAM .1 and TVSSGM.0 are at 2,5 seconds and this shitty ecu is shutting injection straight after I release the gas pedal.
I CANNOT BELIEVE IT. Just to confirm, my maps are defined correctly, arent they? (see pic) ECU i'm working on is 06A906018AQ (ori bin attached). Have been using good 8D0907558E damos to compare maps (in this ecu the TVSAM delay works!!), and 06A906018CG Golf .ols file that floats around the forum to compare too and find maps in M3.8.3. Thanks in advance to everybody. Best regards EDIT: I have confirmed that M3.8.3 ecu, whether is AQ or CG software, does not go through IDLE before Overrun, no matter what value is inserted. M3.8.2 558E and 557T do go from Part Throttle - Idle for 1 sec as specified (got gargles) - then Overrun. Hope somebody can help! Thanks. (https://i.postimg.cc/rs9vkR62/2.jpg) |