|
Title: Cannot connect to ecu Post by: marty.h on June 09, 2012, 01:49:26 PM This is the log im getting any ideas where im going wrong
Validated FTDI device is in dumb mode. Disconnected Connecting... Starting slow init connection. Connecting to address 0x01. Slow init succeeded. Switching to KWP1281 session. KWP1281 connect info: 8D0907551E 2.7l V6/5VT G 0002 Connecting to address 0x01. Slow init succeeded. Switching to KWP2000 session. Connected Disabling Windows sleep mode. Reading all ECU info. Starting diagnostic session. Disconnecting because no response was received for the Tester Present message. Disconnected Reading all ECU info failed. 100% complete. Restoring Windows sleep mode. Starting loading of info. Cancelling loading of info. Starting loading of info. Cancelling loading of info. Switching to KWP2000 session. Validated FTDI device is in dumb mode. Disconnected Connecting... Starting slow init connection. Connecting to address 0x01. Slow init succeeded. Switching to KWP1281 session. KWP1281 connect info: 8D0907551E 2.7l V6/5VT G 0002 Slow init succeeded. Switching to KWP2000 session. Connected Disconnecting because no response was received for the Tester Present message. Disconnected Switching to KWP2000 session. Validated FTDI device is in dumb mode. Disconnected Connecting... Starting slow init connection. Connecting to address 0x01. Slow init succeeded. Switching to KWP1281 session. KWP1281 connect info: 8D0907551E 2.7l V6/5VT G 0002 Disabling Windows sleep mode. Starting variable reading. Starting diagnostic session. Disconnecting because no response was received for the Tester Present message. Disconnected 100% complete. Stopped reading variables. Restoring Windows sleep mode. Starting loading of DTCs. Cancelling loading of DTCs. Switching to KWP2000 session. Validated FTDI device is in dumb mode. Disconnected Connecting... Starting fast init connection. Connecting to address 0x01. Fast init sent, sending start communication request. Start communication request did not receive any response. Disconnected Connecting... Starting fast init connection. Connecting to address 0x01. Fast init sent, sending start communication request. Start communication request did not receive any response. Disconnected Connecting... Starting fast init connection. Connecting to address 0x01. Fast init sent, sending start communication request. Switching to KWP2000 session. Connected Disabling Windows sleep mode. Reading all ECU DTCs. Starting diagnostic session. Diagnostic session mode does not match requested mode. Successfully started diagnostic session. Diagnostic session mode does not match requested mode. Reading all ECU DTCs failed. 100% complete. Restoring Windows sleep mode. Disconnecting because no response was received for the Tester Present message. Disconnected Switching to KWP2000 session. Validated FTDI device is in dumb mode. Disconnected Connecting... Starting slow init connection. Connecting to address 0x01. Slow init succeeded. Switching to KWP1281 session. KWP1281 connect info: 8D0907551E 2.7l V6/5VT G 0002 Connecting to address 0x01. Slow init succeeded. Switching to KWP2000 session. Connected Disconnecting because no response was received for the Tester Present message. Connecting... Starting slow init connection. Connecting to address 0x01. Slow init succeeded. Switching to KWP1281 session. KWP1281 connect info: 8D0907551E 2.7l V6/5VT G 0002 Connected Disabling Windows sleep mode. Reading all ECU info. Starting diagnostic session. Successfully started diagnostic session. Negotiating communication timings. Successfully changed to new communication timings. 0% complete. 25% complete. 50% complete. 75% complete. 100% complete. Read 4 ECU info entries: 0x92, System Supplier ECU Hardware Number: 0261206376 0x94, System Supplier ECU Software Number: 1037350221 0x9B, Calibration Date: 8D0907551E , 0002, 0x0000164F, 0x00000000, 0x009D, 2.7l V6/5VT , 0x9C, Calibration Equiment Software Number: 0x80030000 Restoring Windows sleep mode. Disconnecting because no response was received for the Tester Present message. Disconnected Any ideas what is causing Thanks in advance Marty Title: Re: Cannot connect to ecu Post by: marty.h on June 10, 2012, 11:49:08 AM Anyone ?
will this software work with a 1999 S4 Cheers Marty |