NefMoto

I translated these to English they are from a 022906032CA ME7.1.1 VR6 included is Full Prokon% , and Memory Locations. Let me know if it's helpful, and what you find. Let me know if you need Damos and Hex! ;)

I didn't realize that there were 3 different sets of files...So I included all and a bonus OLS file I translated into English.

https://drive.google.com/file/d/1HaY_zTZw31MQDCKoDxTDCHcqU9_Wwb-g/view?usp=sharing

Here is the link: https://drive.google.com/file/d/1XPTxGHrw6FTMBcX4vu0mO4y6N0eXyw-C/view?usp=sharing

Wow it's late

I sent the EEPROM and not the EPROM here is everything:  https://drive.google.com/file/d/1eEtHRHrhYX3cDfSH8YK8sH2b8WjSJJUz/view?usp=sharing

Need access .

Ok I figure it out! Thanks

It should be good now!  ;D

I didn't realize that there were 3 different sets of files...So I included all and a bonus OLS file I translated into English.

https://drive.google.com/file/d/1HaY_zTZw31MQDCKoDxTDCHcqU9_Wwb-g/view?usp=sharing

Good info, thanks for sharing!

Also memory addresses allow you to use r32logger program if you have that ecu.

Not sure about the contents in the folders though, they look like something form internet damo CDs

Yes downloaded stuff, Still trying to figure out stuff...For Years. It's helped having things in English.

The memory locations in the txt folder in your all.zip actually refer to files in the first link. Had me confused for a while. I haven't the time to go through it slowly now, but it seems to have many functions listed, that the a2l alone can't provide. Handy indeed, especially for asm noobs.

Thanks for looking...I haven't had much time either. I am working on a custom V12 Harness with (4) 38 pin ports for a breakout box. At some point I will be able to put what I have learned on this site to practice.  ;D

Tell you what, that big txt file is something else! All functions are there and god knows what else. Ive never come across such a file in all the damos crap I have purchased.
 Im going to make a fully defined decompiled ida file with it. It will be useful to locate those functions in other me7 me7.11 by code matching

Yes! LOL, and the IDA stuff sounds awesome.

I'm using (2) Early ME7.1 022906032E 0261206619 VR6 ecu's. I ordered from the UK. I played with the A4 3.0L, Porsche Cayenne 955 VR, Touareg 3.2 and the TT 3.2. I then found that the 022906032E Fit the bill with one set of O2's ((1) wide, and (1) Narrow band), and (1) cam sensor.  I have a bang bang (on off) intake cam adjuster which I'm hoping to control with the intake change over output. Can't wait.

this thread needs IROM of 022906032CA

Whats the proccessor marking in this ECU? Pictures would be nice.

Unfortunately I don't have access to such ECU. If I did I would have read it myself :-)
Any ST10 me7.1.1 IROM is of interest.Perhaps there are only a few versions out there.

The CA is not an ST10

Ok, my bad. I've mostly worked with me7.1 and old me7.1.1. It looks like the 032CA have a CPU with IROM, because the first 32k in flash does not line up with CODE XREFS when loaded at @0x0 .

edit:
Found what I needed.

I've been using IDA on this and seem to be doing well. Manually did the whole flash. Now working on the boot rom.

 Just a quick question, in the boot rom there are a load of jumps to the flash that jump back to themselves. Like the one after the reset handler, jumping to 820004, which jumps back to 820004. Have I made a mistake?

The CPU bootrom is (usually) mirrored in a read flash file, depending what kind of hardware was used and what method.
Though it might or might not actually match the CPU rom, so dont use it for any decent purpose, rather use the original depending on the cpu rev.