NefMoto

Hi Guys,

Can someone send me a Definition file (XDF) as per title. Been looking around and can't seem to locate.

Many thanks

Aminder

I can make you one, but I am not going to do this for free...

How much? and what do you require?

Was hoping someone had already done this - is there some guide to attempt to do this myself? Would be interested in learning the process.

I'll PM.

As for a guide - unlikely. There is not a guide for everything.
If you can't figure it out with a hex editor and ida pro, then you will just not figure it out...

Thanks will await you IM.

Hi guys,

I hate asking for handouts, but I couldn't get the R32 file on here to offset against the CP.  Does anyone have any definition files for the CP? 

Also, any advice for gains?  They've got a horrendous flat spot as stock and I'd like to remove it.  I guess IRL/IOP is dead in the midrange.  KFPED could do with being less sensitive too.

I did a partial def file on it at least ages ago, probably did virtually a full one - files all over different hard drives at the mo, I've also just uploaded a csv from a mk5 I got from the "Nefmoto 10,000+" thread (I think -  if it's a file in those links for ME7.1.1. I've probably done something on it for def).

Drop us a message or post up a few map/function locations you're after if you need me to post a csv of the locations of them.

The throttle is WOT all the time with stock tune, it's got nothing to do with it.

I couldn't get anything to line up.  Must be going crazy. I'll have a look again, but I wasn't successful at all.

What causes the flat spot?

Set lamda 0.85, test what a bit more ignition advance would do, test cam advance/retard, test intake manifold flap switch rpm.

please find attached.

im still figuring things out. i downloaded winols and tunerpro. so if i have this correct, its the difinition file that i import that shows me where everything is? correct?

i want to try a crackle and pop
and post cat sensor delete

please checksum my post, where needed!

In for replies.  I can't define the CP.  It gives me a headache.

Im not entirely sure how to assist in the CP?
Im not sure if the car has had an ecu changed before, as its a restoration project of mine. so what are the options of CP abbreviations?

BUMP! help

any idea if anything has happened here? Im looking for the file aswell

did you get a map definition file for this ecu?

No, that's why I commented on your thread.

Are you?  Couldn't have guessed.

Guys, please stop creating new threads.

Merged 3 threads into one.

what map do you need i csn find em quick

I'm just lazy and was hoping someone has a def.  Not sure why they're flat stock and how to get rid of it.

Marty for the noob over here, could you explain what you are offering?
could you explain what the difference is between my ecu and the CB?
both for the mk4 r32

I am a noob, but i'm willing to learn, i wanted to try and use the information, i found on the forum archive and use the index to define the map packs? this is the manual way of doing things but i guess i dont have a choice(very unsure of what goes where), is this called xdf(definition file?)
i wanted to compare the two(mine vs attached)
???question, am i understanding the idea of definition file correctly???>>map identification?

Hi guys

from what i understand. i open the hex file using winols.
then i go to the address where winols suggests a "MAP" is.
i varify this "map" address and size with that of the excel sheet?
i create the"map"
add a description. and boom its under my maps.

question!! the map disapears when i close winols. where do i save these"my maps"

what version of winols is better. any help here? am i even on the write track?

"Project - save" or the little floppy disc looking icon when you create a map. 

/
hi, did you have a look at the excell sheet to confirm whether those map locations would comply with my ecu

I'm a fan of liner KFPED, but my car is swapped so fwd only. Sadly i have no def but im watching this tread and will help if i can.

i paid for a map pack

Are you going to upload it?

What excel sheet? You can def any mk4 one with the files on here really, there's only a few bytes added here and there so you can see the hex figures around them so you just shift the offset a touch and re-define.

Take a look here, the green 05's at the bottom, you can see that before them if you follow it, it goes 96, 7D, 64 etc all the way to the 00, 05, 50 bit then you can see added values there before the FF, FC bits - that's all the differences there are, easier if you try and see those patterns though if you're planning on spending time on it;

(https://farm1.staticflickr.com/977/41480874404_dd45a2ee71_b.jpg) (https://flic.kr/p/26cwjMJ)032CP CW Noromchkreset online file (https://flic.kr/p/26cwjMJ) by Rick B (https://www.flickr.com/photos/146155164@N03/), on Flickr

Thank you. im a noob,
but i am willing to learn, this is exactly what i meant to ask,
i see from the screen shot you have a r32 turbo file, i will need a basic map to get my car going once all my parts arrive. i will start a new forum about my build. i havent had look at my mapping as yet since my radiator had a crack in it. so i moved my battery to the boot, and is currently installing the aluminium radiator.

The techchy bits you need to understand for good FI control and monitoring for the large increases in air (density);

(Seems to be a bit rubbish under Google for some reason if you can't see it...)
https://www.google.co.uk/search?q=fuedk+nefmoto&oq=fuedk+nefmoto&aqs=chrome..69i57j69i60.4964j0j7&sourceid=chrome&ie=UTF-8

The important bits to learn here if you're serious;
https://app.box.com/s/7fvt652zoqapzmfq7fv0rfufs96yv25q

Yes I've done a dozen or so FI R32's or any NA ME7.1.1.'s I can set you up with some basics but you'll do well reading the bits I post to know what troubles you may face though!

Hi, Did anyone end up making a definition file for this in the end?

Thanks

Not he same but all i have for ME 7.1.1 3.2L