|
Title: Need Help with these Logs, Dont really know what im looking for.. Post by: longliveaudi on October 30, 2012, 03:06:27 PM Im stage 3, was hitting 24 psi before front o2 sensors fail'd, then when i installed both front new o2 senors i peak at 13-14 psi WOT with lots of misfires.. if i hold boost.
Im not to sure what im looking for but as you can see i pull up these logs and codes from vag com. yes i have deleted them many times and they come right back on after 5 min of driving. What else should i log and is there a chart i can compare numbers. 16534 - Oxygen (Lambda) Sensor B2 S1 P0150 - 35-10 - Malfunction in Circuit - Intermittent 16514 - Oxygen (Lambda) Sensor B1 S1 P0130 - 35-10 - Malfunction in Circuit - Intermittent 15:44:45 Group 030: Lambda Control (Sensor Status) 111 Bank 1 Sensor 1 100 Bank 1 Sensor 2 111 Bank 2 Sensor 1 100 Bank 2 Sensor 2 15:44:45 Group 031: Lambda Control 0.050 V Bank 1 Sensor 1 (actual) 0.000 V Bank 1 Sensor 1 (specified) 0.075 V Bank 2 Sensor 1 (actual) 0.000 V Bank 2 Sensor 1 (specified) -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Address 01: Engine (8D0 907 551 M) 15:45:56 Group 001: General 880 /min Engine Speed (G28) 94.0°C Coolant Temperature (G62) 25.0 % Lambda Control Bank 1 19.5 % Lambda Control Bank 2 15:45:56 Group 030: Lambda Control (Sensor Status) 111 Bank 1 Sensor 1 100 Bank 1 Sensor 2 111 Bank 2 Sensor 1 100 Bank 2 Sensor 2 15:45:56 Group 031: Lambda Control 0.060 V Bank 1 Sensor 1 (actual) 0.000 V Bank 1 Sensor 1 (specified) 0.135 V Bank 2 Sensor 1 (actual) 0.000 V Bank 2 Sensor 1 (specified) -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Address 01: Engine (8D0 907 551 M) 15:46:05 Group 001: General 880 /min Engine Speed (G28) 94.0°C Coolant Temperature (G62) 25.0 % Lambda Control Bank 1 18.0 % Lambda Control Bank 2 15:46:05 Group 030: Lambda Control (Sensor Status) 011 Bank 1 Sensor 1 100 Bank 1 Sensor 2 111 Bank 2 Sensor 1 100 Bank 2 Sensor 2 15:46:05 Group 031: Lambda Control 0.060 V Bank 1 Sensor 1 (actual) 0.000 V Bank 1 Sensor 1 (specified) 0.070 V Bank 2 Sensor 1 (actual) 0.000 V Bank 2 Sensor 1 (specified) -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Address 01: Engine (8D0 907 551 M) 15:49:25 Group 001: General 880 /min Engine Speed (G28) 93.0°C Coolant Temperature (G62) 25.0 % Lambda Control Bank 1 19.5 % Lambda Control Bank 2 15:49:25 Group 033: Lambda Control 25.0 % Lambda Control Bank 1 Sensor 1 0.065 V Sensor Voltage Bank 1 Sensor 1 18.0 % Lambda Control Bank 2 Sensor 1 0.635 V Sensor Voltage Bank 2 Sensor 1 15:49:25 Group 035: Lambda Control (Lambda Sensor Aging - Bank 2 Sensor 1) 880 /min Engine Speed (G28) 330.0°C Catalytic Converter Bank 2 Temp. 0.00 s Dynamic Factor Bank 2 Sensor 1 Test OFF Result Lambda Aging -------------------------------------------------------------------------------- -------------------------------------------------------------------------------- Address 01: Engine (8D0 907 551 M) 15:53:58 Group 001: General 880 /min Engine Speed (G28) 92.0°C Coolant Temperature (G62) 0.0 % Lambda Control Bank 1 0.0 % Lambda Control Bank 2 15:53:58 Group 033: Lambda Control 0.0 % Lambda Control Bank 1 Sensor 1 0.025 V Sensor Voltage Bank 1 Sensor 1 0.0 % Lambda Control Bank 2 Sensor 1 0.035 V Sensor Voltage Bank 2 Sensor 1 15:53:58 Group 035: Lambda Control (Lambda Sensor Aging - Bank 2 Sensor 1) 880 /min Engine Speed (G28) 395.0°C Catalytic Converter Bank 2 Temp. 0.00 s Dynamic Factor Bank 2 Sensor 1 Test OFF Result Lambda Aging Title: Re: Need Help with these Logs, Dont really know what im looking for.. Post by: professor on October 30, 2012, 03:09:21 PM Both lambda sensors gives DTCs.
Can you clear those DTCs? After clearing these they appear again? Title: Re: Need Help with these Logs, Dont really know what im looking for.. Post by: nyet on October 30, 2012, 03:28:59 PM Next time please click "new topic", not "new poll".
Title: Re: Need Help with these Logs, Dont really know what im looking for.. Post by: longliveaudi on October 30, 2012, 03:45:21 PM Both lambda sensors gives DTCs. Can you clear those DTCs? After clearing these they appear again? Yes. ....these logs and codes from vag com. yes i have deleted them many times and they come right back on after 5 min of driving. What else should i log and is there a chart i can compare numbers. Title: Re: Need Help with these Logs, Dont really know what im looking for.. Post by: jdm ej1 95 on October 30, 2012, 04:07:07 PM stupid question but..
did you swap the correct sensors? both black plugs... not the green plug/brown plug and what sensors did you replace with OEM or universal wire-in type.. also we cant be left to assume things... did both o2s go at the same time? if so i doubt its the actual sensors... what stage 3 are you. what tune.. etc.. give us info. Title: Re: Need Help with these Logs, Dont really know what im looking for.. Post by: longliveaudi on October 30, 2012, 06:44:50 PM stupid question but.. did you swap the correct sensors? both black plugs... not the green plug/brown plug and what sensors did you replace with OEM or universal wire-in type.. also we cant be left to assume things... did both o2s go at the same time? if so i doubt its the actual sensors... what stage 3 are you. what tune.. etc.. give us info. I replaced with the bosch OE smartlink kit i dont know if your seen these but the smartlink kit is only the o2 sensor part with pigtails so i had to cut the original o2 sensor, use the old connector, splice the new o2 senor with the old connector. sorry if this was confusing heres a link: http://www.boschautoparts.com/BAP_Te...allGDWEB09.pdf Yes i did both at the same time because my vag brought up both front priamry o2 sensor codes. did both the black ones but im sure my wiring was correct, all the wires matched up by color, conected them correctly now this. im stage 3+ i think..k04's, side mounts, rs4 ypipe, apr bipipe, downpipes, exhaust of course, etc. 034 550cc k04 base tune need more info let me know thanks Title: Re: Need Help with these Logs, Dont really know what im looking for.. Post by: jdm ej1 95 on October 30, 2012, 07:25:33 PM Read the instructions.. I think the universal wire sensors actually have the same colors but wire up different..
Title: Re: Need Help with these Logs, Dont really know what im looking for.. Post by: nyet on October 30, 2012, 08:50:46 PM You should not have tried this w/o having more of an idea of how your ecu works, what kind of O2 signals it expects, and how to interpret codes and logs.
Also, that URL to the pdf is obviously not right. Title: Re: Need Help with these Logs, Dont really know what im looking for.. Post by: longliveaudi on October 30, 2012, 09:19:48 PM You should not have tried this w/o having more of an idea of how your ecu works, what kind of O2 signals it expects, and how to interpret codes and logs. Also, that URL to the pdf is obviously not right. my mistake thats a pdf file above, here is the working link http://www.boschautoparts.com/oxygensensors/pages/premiumsmartlink.aspx |