|
Title: IMMO3 OFF help request Post by: UrbanAssaultar on November 22, 2012, 02:41:51 PM Got a spare 4Z7 907 551 S ME7.1.1 ECU and I am trying to get IMMO turned off, was successful to get a EEPROM dump with ArgDub's ME7_95040 - EEPROM tool. Looking at the dump file with the hex editor in TunerPro, I am not finding anything in the search on which values to change. Any help would be much appreciated.
Title: Re: IMMO3 OFF help request Post by: matchew on November 22, 2012, 03:02:31 PM Search more, the answer is on this forum in more than once place.
Title: Re: IMMO3 OFF help request Post by: UrbanAssaultar on November 22, 2012, 10:46:55 PM Search more, the answer is on this forum in more than once place. I tried the clone route and this is the error that comes up when I try and read out data from the ECU installed in the car. There was no point reading to a file because it fails every time, so I printed contents to screen instead. Ver: 1.31 Com Port: 4 Baud Rate: 10400 Opening COM4 ... OK Initiating communication ... OK ECU ID response: 4Z7907551R U25AN34.hex LEV G x SoftCod: 07755, WSC: 21583 Reading EEPROM ..............................................................FAIL. (error=0x01) Closing COM4 Here is the read data log from the bench (spare) ecu Ver: 1.31 Com Port: 4 Baud Rate: 10400 Opening COM4 ... OK Initiating communication ... OK ECU ID response: 4Z7907551S 2.7L V6/5VT G 0020 SoftCod: 07755, WSC: 02334 Reading EEPROM .............................................................. OK File saved Closing COM4 ECU installed in the car is a 551S box with a 551R.bin file with SAI removed. Title: Re: IMMO3 OFF help request Post by: aef on November 23, 2012, 12:26:15 AM Have you tried bootmode?
Title: Re: IMMO3 OFF help request Post by: UrbanAssaultar on November 23, 2012, 07:15:36 AM Yes, boot mode works with the spare ECU and I can write to it under that mode. I didn't save a log for that process though. I used APR's IMMO clone software also with no success. It threw a fit when I tried to write data saved from the car ECU to the bench ECU. I realize these files mean nothing because of their format, but I have attached them anyway.
Title: Re: IMMO3 OFF help request Post by: Drehkraft on February 16, 2013, 08:16:57 PM Did you get yourself sorted? The info you need is posted on this forum.
Title: Re: IMMO3 OFF help request Post by: UrbanAssaultar on February 16, 2013, 08:25:46 PM Not quite, on the to-do list. I had my original ecu tuned, this is just a spare to tinker with.
Title: Re: IMMO3 OFF help request Post by: Drehkraft on February 16, 2013, 08:40:04 PM Fixed.
Title: Re: IMMO3 OFF help request Post by: UrbanAssaultar on February 16, 2013, 08:45:19 PM I'll hook up my bench flash setup and report back, thank you.
Title: Re: IMMO3 OFF help request Post by: Drehkraft on February 16, 2013, 08:57:04 PM For future reference:
12 +1 22 +1 line checksum 1e & 2e subtract 1 from each. Title: Re: IMMO3 OFF help request Post by: UrbanAssaultar on April 28, 2013, 10:32:54 AM For future reference: 12 +1 22 +1 line checksum 1e & 2e subtract 1 from each. Finally got off my duff and got it done: (http://images.quattroworld.com/proxy.svc/Images/Image?id=0d5bd2dc4a22420790ac0d61728ad8ef.jpg) Title: Re: IMMO3 OFF help request Post by: jshaw on May 20, 2013, 09:54:42 PM can any one verify that i have correctly disable immo in this file.
problem is i know the skc for this file is 06041 but when i tried to adapt it with VCDS error is coming ( incorrect login code try after sometime). can any one tell me where in this file skc is 5e28 as said in this forum or 9917. regards Title: Re: IMMO3 OFF help request Post by: jshaw on May 21, 2013, 09:30:23 AM Never mind , i tested it and it worked flawlessly .
great forum learned a lot though i was very passive user in terms of contributing because i don't know much as of now. regards |