|
Title: Immo off for ME3.8.2 Post by: kolbenmann on January 29, 2013, 05:20:34 PM Hello:
I just swapped a new instrument cluster on a project and now I need to immo off this file. I hope someone could give me a hand Title: Re: Immo off for ME3.8.2 Post by: ddillenger on January 29, 2013, 05:22:44 PM oooh-I can do this.
Two seconds. Title: Re: Immo off for ME3.8.2 Post by: ddillenger on January 29, 2013, 05:39:42 PM Try this.
Title: Re: Immo off for ME3.8.2 Post by: kolbenmann on January 29, 2013, 06:42:09 PM Try this. WOW that was fast!!! :o thanks a lot for your support, I'll test right away and let you know Title: Re: Immo off for ME3.8.2 Post by: aef on January 30, 2013, 03:05:15 AM Kolbenmann im not sure if you know this but you can check the immo with vagcom at channel 91.
With my method, the immo off file would look a little different. So please try and report back! Title: Re: Immo off for ME3.8.2 Post by: icezero on January 30, 2013, 05:06:03 AM @aef the off file is ok and worked 100% i have done it on same way :-)
Title: Re: Immo off for ME3.8.2 Post by: LechnerTuning on March 17, 2013, 01:54:12 AM Hello,
we have ME3.8.3 here, its the 24C02 8 pin eprom right, which programer do you use to read/write it, we have the willem here but no suitable socket available ? I heard that there are programers which can read/write this 24C02 even if they are still on the pcb ? Thank you Title: Re: Immo off for ME3.8.2 Post by: k0mpresd on March 17, 2013, 04:47:40 AM gq3x + test clip.
Title: Re: Immo off for ME3.8.2 Post by: LechnerTuning on March 17, 2013, 07:54:49 AM Anybody has the connections ?
Title: Re: Immo off for ME3.8.2 Post by: k0mpresd on March 17, 2013, 08:04:19 AM Anybody has the connections ? www.mcumall.com/ Title: Re: Immo off for ME3.8.2 Post by: Drehkraft on March 17, 2013, 09:35:16 AM www.mcumall.com/ 2nd that. http://www.mcumall.com/comersus/store/comersus_viewItem.asp?idProduct=4406 Title: Re: Immo off for ME3.8.2 Post by: Drehkraft on March 17, 2013, 09:36:29 AM Just one note - you usually have to apply + power to the W pin (write protect). An unpowered ECU normally holds the line down. I just jumper power from the + pin to that one.
Title: Re: Immo off for ME3.8.2 Post by: LechnerTuning on March 17, 2013, 10:49:09 PM Isnt there any chance to connect without this adapter, it will take weeks until it will arrive here.
So just soldering the wires direct to the Eeprom and connect it to GQ3X ? Title: Re: Immo off for ME3.8.2 Post by: aef on March 18, 2013, 05:21:42 AM Yes it is possible. Search for the 24c02 in your GQ Software and you will see a small picture where to place the chip and the direction.
Title: Re: Immo off for ME3.8.2 Post by: LechnerTuning on April 10, 2013, 04:45:06 AM Hello,
orderd the stuff from mcumall but when I try to read it, it just reads out zeros. But I assume its corrected ok because when I completely remove it then it just reads zero. Anybody met this before ? Title: Re: Immo off for ME3.8.2 Post by: aef on April 10, 2013, 05:40:41 AM more details please
maybe screenshot? Title: Re: Immo off for ME3.8.2 Post by: LechnerTuning on April 10, 2013, 06:37:24 AM Attached
Title: Re: Immo off for ME3.8.2 Post by: auamanu on June 13, 2013, 04:02:50 AM Which maps have you change on the M3.8.2 to deactivate immo?
Title: Re: Immo off for ME3.8.2 Post by: ddillenger on June 13, 2013, 03:58:32 PM Which maps have you change on the M3.8.2 to deactivate immo? You need to pull the contents of the eeprom. This is NOT the same as the flash memory containing the maps. Title: Re: Immo off for ME3.8.2 Post by: Giannis on July 21, 2013, 02:01:29 AM This immo file posted here is for all m3.8.2? I have a spare ecu for testing that i am trying to immo off for a long time now. I don't have original file the 24c02 burned :(. Any help would be great.
|