|
Title: ME7.1/7.5 immo-off bin Post by: ddillenger on February 25, 2013, 09:30:01 PM I have used this on many ecu's with no issues. Make sure to use the 7.1.1 file if you don't have an me7.1/7.5 ecu.
Title: Re: ME7.1/7.5 immo-off bin Post by: aRd on February 26, 2014, 11:10:58 PM Thank you for sharing
Title: Re: ME7.1/7.5 immo-off bin Post by: userpike on March 16, 2014, 09:06:46 AM I flashed this immo off .bin and got rid of the "immo not authenticated" error msg in Nef but I still get that the ECU has rejected security access and it won't let me go through with the reading or writing. What am I missing here?
This is for an HSbox that looks as if it had an LP file flashed to it from the dealer. I heard they do this now because the HS software has been superseded. I don't see how this should matter though. Title: Re: ME7.1/7.5 immo-off bin Post by: c11rgd on May 26, 2014, 02:54:45 PM I have used this on many ecu's with no issues. Make sure to use the 7.1.1 file if you don't have an me7.1/7.5 ecu. so can i use this to immo off the following ecu. TT 225HP APX 8N0906018AE ME7.5 0261207030 as im using the engine in a mk1 golf conversion. Title: Re: ME7.1/7.5 immo-off bin Post by: Bi-turbo on September 10, 2014, 01:30:08 AM Just to confirm.
Would i flash this bin as normal (bootmode + galletto) If i then flash a file onto the car will it not put the immo back on if that bin file hasnt had immo off??? Title: Re: ME7.1/7.5 immo-off bin Post by: Bi-turbo on September 10, 2014, 01:35:39 AM Ignore the above...
I would use the 95040 program to flash the immo bin to the ecu which is different to the eprom if im correct? Title: Re: ME7.1/7.5 immo-off bin Post by: turboat on September 10, 2014, 03:49:02 AM The convention on this site is:
- Flash - where the maps go (512kb or 1024kb) - eeprom - where the immo data goes (512 or 1024bytes - i.e. 1024x smaller than the flash). The immo bin on this page is for the eeprom, which is different from the flash where the maps are stored. You are correct, that you should use argdub's me7_95040 tool to write the eeprom. However, I would always read the eeprom contents from the ecu, modify it for immo-off, and then write it back, rather than writing a generic immo-off. Title: Re: ME7.1/7.5 immo-off bin Post by: Bi-turbo on September 10, 2014, 04:20:05 AM Thanks for the clarificaion
Ive looked at the immo bin in hex editor, is the immo at the same address in all ME7.1/7.5? Could like you said just edit the hex with what is in the immob bin? if that makes sense Thanks in advance Title: Re: ME7.1/7.5 immo-off bin Post by: turboat on September 10, 2014, 05:30:33 AM 7.1 and 7.5 seem to be the same, 7.1.1 is slightly different.
I usually use my tool to do immo off, because I can never remember how to set the checksum properly, but its super easy with a hex editor too. http://nefariousmotorsports.com/forum/index.php?topic=6134.15 As I did to a spare ecu this morning: 1. Read from ECU. (me7_95040 --OBD -r -p 1 eeprom.bin) 2. view info (eepromtool --in eeprom.bin) 3. turn off immo (eepromtool --in eeprom.bin --out eeprom_off.bin --immo off) 4. write back to ecu in boot mode (me7_95040 --bootmode -w -p 1 eeprom_off.bin) took about 10 minutes. If you get a complaint about a checksum error on a virgin eeprom that you've just read from a virgin/working ecu, please post up on the thread for the tool. |