|
Title: Tried and Fail Cluster Post by: staycute on May 17, 2013, 10:37:12 AM Ok. So I was trying to do the fis cluster swap on my 04 r32. Used Vag Commander 2.5 to retrieve my login. So I go ahead and do the swap and follow the instructions as listed on vcds. After everything I got a immo activated error on cluster. No worries. I decided to swap back to the original cluster. No immo light or anything looked normal. But now the car doesn't start. The engine cranks but not dice. I'm assuming this is an issue with the cluster now. Anyone have an idea how I can just go back to the original cluster and act like nothing happened?
Title: Re: Tried and Fail Cluster Post by: ddillenger on May 17, 2013, 10:43:14 AM Unhook the battery for 5 minutes, plug it back in, clear all codes, then the car should start.
Title: Re: Tried and Fail Cluster Post by: staycute on May 17, 2013, 10:47:21 AM Unhook the battery for 5 minutes, plug it back in, clear all codes, then the car should start. Ok, going outside to try it. Right now. Title: Re: Tried and Fail Cluster Post by: staycute on May 17, 2013, 11:09:43 AM Ok, no dice. I scanned it and came up with this
VCDS Version: Release 11.11.5 Data version: 20121222 Friday,17,May,2013,14:03:17:23531 Chassis Type: 1J - VW Golf/Bora IV Scan: 01 02 03 08 15 16 17 19 22 29 35 36 37 39 46 47 55 56 57 75 76 VIN: WVWKG61J64D129373 Mileage: 182540km/113425miles ------------------------------------------------------------------------------- Address 01: Engine Labels: None Part No SW: 022 906 032 EX HW: 14. 4.0 3 Component: United.R32Lc G ÉI/ Coding: 0000132 Shop #: WSC 77872 024 452294 VCID: 65CB9E7DAF3A2D30B2A 1 Fault Found: 17978 - Engine Start Blocked by Immobilizer P1570 - 008 - - Intermittent Readiness: 0000 0000 ------------------------------------------------------------------------------- Address 03: ABS Brakes Labels: 1C0-907-37x-ESP-A.lbl Part No: 1C0 907 379 P Component: ESP ALLRAD MK60 0101 Coding: 0023049 Shop #: WSC 31414 000 00000 VCID: 3777043545166FA0D06 No fault code found. ------------------------------------------------------------------------------- Address 08: Auto HVAC Labels: 3Bx-907-044.lbl Part No: 3B1 907 044 C Component: CLIMATRONIC C 2.0.0 Coding: 11000 Shop #: WSC 31414 VCID: 2143CA6DAB9201100E2 1 Fault Found: 01274 - Air Flow Flap Positioning Motor (V71) 37-00 - Faulty ------------------------------------------------------------------------------- Address 15: Airbags Labels: 6Q0-909-605-VW5.lbl Part No: 1C0 909 605 F Component: 17 AIRBAG VW61 0108 0003 Coding: 12599 Shop #: WSC 31414 VCID: 2757D475C5B6FF20406 No fault code found. ------------------------------------------------------------------------------- Address 17: Instruments Labels: 1J0-920-xx5-17.lbl Part No: 1J0 920 927 AX Component: KOMBI+WEGFAHRSP VDO V05 Coding: 05130 Shop #: WSC 05074 VCID: 81032AED8B526110AE2 WVWKG61J64D129373 VWZ7Z0C8765100 No fault code found. ------------------------------------------------------------------------------- Address 19: CAN Gateway Labels: 6N0-909-901-19.lbl Part No: 6N0 909 901 Component: Gateway K<->CAN 0001 Coding: 00006 Shop #: WSC 05051 VCID: F0E57F29B0F8789851C No fault code found. ------------------------------------------------------------------------------- Address 22: AWD Labels: 02D-900-554.lbl Part No: 02D 900 554 D Component: HALDEX LSC ECC 0011 VCID: 2143CA6DAB9201100E2 No fault code found. ------------------------------------------------------------------------------- Address 46: Central Conv. Labels: 1C0-959-799.lbl Part No: 1C0 959 799 C Component: C7 Komfortgerát HLO 0003 Coding: 00064 Shop #: WSC 31414 VCID: 3777043515166FA0D06 Subsystem 1 - Part No: 1C1959801A Component: C7 Tõrsteuer.FS KLO 0202 Subsystem 2 - Part No: 1C1959802A Component: C7 Tõrsteuer.BF KLO 0202 No fault code found. End --------------------------------------------------------------------- So i cleared it cycled the key off to on and wen to start it again and same problem. What if i turn the immo off with vag commander would you think that would help? Any ideas? Title: Re: Tried and Fail Cluster Post by: ddillenger on May 17, 2013, 11:22:13 AM Vag commander is barely functional. I use it to play with cluster mileage only. Not quite sure what happened honestly.
Title: Re: Tried and Fail Cluster Post by: staycute on May 17, 2013, 11:26:04 AM Honestly i have no clue either. I'll try the adaptation over again and adapt the keys as well and see what going on. I'll try to turn the immo off as well if that even works. ???
Title: Re: Tried and Fail Cluster Post by: staycute on May 17, 2013, 11:31:02 AM By any chance would you happen to know what the reset ecu button does?
Title: Re: Tried and Fail Cluster Post by: ddillenger on May 17, 2013, 11:35:43 AM It disconnects, then reconnects in order to display changes. Never worked for me, only supported on some vehicles.
Title: Re: Tried and Fail Cluster Post by: staycute on May 17, 2013, 11:55:09 AM And the immo on and off are effective only when you write to the eprom i assume right? CLicking them and then exiting without writing wont do anything.
Title: Re: Tried and Fail Cluster Post by: ddillenger on May 17, 2013, 12:00:34 PM I hope you read, and saved the eeprom contents before you did ANYTHING with vag-commander. It has a tendency to corrupt data.
Title: Re: Tried and Fail Cluster Post by: staycute on May 17, 2013, 12:09:33 PM NOOOO, i just read. :'(
Should i now look for an original eeprom? Title: Re: Tried and Fail Cluster Post by: ddillenger on May 17, 2013, 02:42:26 PM 1J0920927A
Two dumps attached, if yours is similar it's probably fine. If you use these you'll have to adapt the immobilizer. Title: Re: Tried and Fail Cluster Post by: staycute on May 17, 2013, 09:30:55 PM Ok, so nothing went well today. My original cluster now has a def under the odometer when the key is in the ignition on position and now the worse part is that i keep getting a fail message when i try to login. I will not let me log in into the cluster when i enter the skc. I am almost at a complete stop.
Title: Re: Tried and Fail Cluster Post by: f1torrents on May 22, 2013, 05:13:29 PM -Where are you located?
-You dont have a original saved dump from the cluster? -Does anyone know if VAG Commander auto saves a recovery file like vagdashcan? I don't use vag commander. Title: Re: Tried and Fail Cluster Post by: staycute on May 22, 2013, 07:41:28 PM I'm in Woodbridge Nj.
I don't have the original dump.(I was too excited) :facepalm: Vag Commander doesn't Title: Re: Tried and Fail Cluster Post by: MK2-VRT on June 12, 2013, 03:11:37 AM DEF message is normaly al wrong dump in eeprom..You can try to recode the cluster or write the original file to your cluster.
Fail in display is mostly a locktime problem, please make a printscreen from measeringblocks 022 - 023 and 024 ( 17-Instruments ) 024 everything must be 0 - 0 - 0 - 0, when no, when you see 9 - 0 - 0 - 0, let the ignition on for 9 min, then login with the right pin en adapt the cluster to the ecu and match the keys..You need both logins from the new cluster and the old cluster. Let us now.. |