NefMoto

I have a 2000s4 and just installed logger and and when im plugged into car and start logger it say ecu #s dont match.. im guessing its wrong bin file?? Ive tried several and none fix the problem. Please help.

Read out your ecu and use that to create a template wnd go from there

How would i do that exactly?

There's a complete read-me in the DOC subfolder.  Search for Quickstart.

If you're asking how to read your ECU in the basic sense, download the Nefmoto software from this site and use that.

ok ive read the ecu with neftmoto software...now how do i creat a bin from that ???

OK I PICKED appropriate memory layout and now when trying to read ecu so i can save the bin and start logging car here is msg i get :
Validated FTDI device is in dumb mode.
Disconnected
Connecting...
Starting slow init connection.
Connecting to address 0x01.
Slow init succeeded.
Switching to KWP1281 session.
KWP1281 connect info: THIS-IS-THE-RAM-PROGRAM-          Connecting to address 0x01.
Slow init succeeded.
Switching to KWP2000 session.
Connected
Disabling Windows sleep mode.
Reading ECU flash memory.
ECU reports programming session preconditions have been met.
Negotiating communication timings.
Timing negotiation failed. Communication timings are unchanged.
Requesting security access.
ECU reports that security access is not supported.
Starting diagnostic session.
Successfully started diagnostic session.
Negotiating communication timings.
Successfully changed to new communication timings.
Requesting security access.
Security access granted.
Validating flash memory starts at 0x00800000 and ends at 0x00900000.
Validation failed, ECU reports RequestUpload service is not supported. RequestUpload may have been disabled by aftermarket engine software.
Memory layout validation failed.
Starting to read data block.
Requesting upload from ECU for address range 0x00800000 to 0x00803FFF.
Request upload from ECU failed, ECU reports service is not supported. Request upload may have been disabled by aftermarket engine software.
Reading ECU flash memory failed. Trying to force ECU to recognize read operation is complete.
Finished forcing ECU to recognize that failed read operation is complete.
Reading ECU flash memory failed.
100% complete.
Restoring Windows sleep mode.
 

any suggestions?? Ive tried using generic .bin file from the archives on this site and when i hit log it ends with final error message of ->

Reading log config file C:\Users\Guest\Desktop\ME7Logger_DIST_02042012_v1.17(
2)\logs\8D0907551AStock(1)_template.cfg .... done
-> Reading ecu characteristics file C:\Users\Guest\Desktop\ME7Logger_DIST_020420
12_v1.17(2)\ecus\8D0907551AStock(1).ecu .... done
Used Ecu definition is:
[Communication]
Connect      = SLOW-0x11
Communicate  = HM0
LogSpeed     = 56000

[Identification]
HWNumber           = "0261206110"
SWNumber           = "1037352345"
PartNumber         = "8D0907551A"
SWVersion          = "0002"
EngineId           = "2.7l V6/5VT"

Logged variables are:
#no.: name                , alias                           , addr  ,sz, bitm, S
, I,  A         ,   B, unit
#-------------------------------------------------------------------------------
-----------------------------
#001: plsol_w             , BoostPressureDesired            , 38219E, 2, 0000, 0
, 0,   0.0390625,   0, 'mbar'
#002: pvdkds_w            , BoostPressureActual             , 38210E, 2, 0000, 0
, 0,   0.0390625,   0, 'mbar'
Logged data size is 4 bytes.
Start connecting to ECU at 30.09.2013 16:58:19.211
try connect slow(11)
=> FLASH (slowinit)
ecuid reports software version
Started session86, speed=56000
-> Read ECU ID's .... done
HWNumber mismatch: need '0261206110', ecu is '0261206776'
=> Logging failed
exiting (cause=0x4)...

C:\Users\Guest\Desktop\ME7Logger_DIST_02042012_v1.17(2)>

'RequestUpload may have been disabled by aftermarket engine software'.
Your ECU looks like it is already remapped mate so probably blocking it.

so all in all I cannot get the the .bin from website to work when trying to log  and i cannot pull .bin from ecu either, its a eurodynee tapp ko4 file on there right now and i want to look at some logs and diagnose car....really having hard time getting up and running. would really appreciate support as ive followed walk through to a T... one

Im not sure but one of the logs you posted shows that you need a .bin file with the HW number : '0261206776' you was trying to use HW number : '0261206110'
Try searching for the correct HW number then give it a shot

THank you, my car is supposed to be a box but would not run that file so i ran G and it worked great, Also i believe you need to pick specific usb port or it will have errors that will further distract.. thanks nefmoto community for amazing product.

Glad you got it all sorted  :)