NefMoto

I will put everything in this topic when I'll have processed all the info :) Right now I would like some confirmations and some additional info:
** If I understand diagrams correctly in ME7.5 we use szrl_w and in MED9 it is szout. Am I correct?
** If i'm correct in my first statement, then how do we play with KFSZT & FSZTM? What to do with ME7's szout_w and what value it should be set to? Why MED9 has no szrl_w?


I have made complete diagrams for this module (attached to this post) so everyone could take a look and comment... Right now I have done ~90% transfer of all these maps, but need these last two questions answered.. Tommorow I will update this topic with whole list of maps to transfer from TFSI with correct values so you wouldn't even need to search.

As promised some progress here...

SA :::
---------------------------------------------------------
NMNZUESA == NMNZUESA
NMXZUESA == NMXZUESA

LASTDYN ::: (DISABLED, BECAUSE CW_SZTRL.0 = 0)
---------------------------------------------------------
CWDMFAB.0 = 0 (b_lsd = 0!)
DTSDRL = FF (drlsolf_w == load change in 10ms!)

BAND/FFZ :::
---------------------------------------------------------
FUBAOF = FUBAOF
CW_FUBND.0 = 1
FWNMOT = FWNMOT
KFFFANZ = KFFFANZ
FFLDZ = FFLDZ

Now some questions arise:
When ME7.5 uses szout_w and when szrl_w??? in MED9 there's only szout_w. If I translated correctly szrl is limited dwell time. So when is this applied in ME7.5 ecus?
Also in ME7.5 what is value of SY_FFZ constant?

Some general notes: In ME7.5 szrl_w looks like szout_w in MED9. LASTDYN submodule is disabled in MED9. Also there is some submodule name differences in both ecus (FFZ vs BAND).

Work continues...

Updates...

SA :::
---------------------------------------------------------
NMNZUESA == NMNZUESA
NMXZUESA == NMXZUESA

LASTDYN ::: (DISABLED, BECAUSE CW_SZTRL.0 = 0)
---------------------------------------------------------
CWDMFAB.0 = 0 (b_lsd = 0!)
DTSDRL = Fs (drlsolf_w == load change in 10ms!)

BAND/FFZ :::
---------------------------------------------------------
FUBAOF = FUBAOF
CW_FUBND.0 = 1
FWNMOT = FWNMOT
KFFFANZ = KFFFANZ
FFLDZ = FFLDZ

MAIN :::
---------------------------------------------------------
KFTSRL = KFTSRL
FSWTM = FSZTM
TSMXNL = TSMXNL
TSMNSA = TSMNSA
TSMX = TSMX
DUBZS = 0s
KFSZDUB = KFSZDUB
KFTSDYN = 1s
FTOMN = 0.1
FSZTM = FSZTM
KFSZT = >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
10.0   8.0   5.2   3.0   2.8   2.6   2.3   1.8
10.4   8.4   4.1   2.7   2.5   2.4   2.1   1.4
10.4   8.4   4.1   2.7   2.5   2.4   2.1   1.4
10.0   8.0   4.0   2.6   2.4   2.3   2.0   1.4
10.4   8.4   3.7   2.5   2.3   2.2   1.9   1.3
10.5   7.5   3.2   2.3   2.2   2.0   1.7   1.2
10.5   5.6   2.9   2.1   2.0   1.8   1.6   1.1
10.6   4.5   2.6   1.9   1.8   1.7   1.5   1.1

Some notes: I didn't know what to do with KFSZT because MED9 doesn't have any dwell time map that is based on ub and nmot. So I kinda iprovised (check attached xls) and produced my own version. Also FTOMN I have chosen to set to 0.1 and not 0 just because it kills my coils (if used with NLS/AL/LC asm code).

Still, it would be nice to know how Me7.5 ecu chooses szout_w or szrl_w variable? Also need to know 100% that szrl_w is then main dwell time in me7.5 and not szout_w.

Oh, since SA is disabled in MED9 you do no need TSMNSA :)

What's the benefit of making these map changes to the me7 over just running as a lot of people do

Increased coil life.

Hi guys. I am new to this forum. I have installed red TFSI coils. Help me find the card addresses described by masterj

KFTSRL
FSZTM
TSMXNL
TSMNSA
TSMX
DUBZS
KFSZDUB
KFTSDYN
FTOMN
FSZTM
KFSZT

Can these values replace stock values on 551r ecu on a BEL allroad using stock push down coils?