|
Title: Strange Error 8E0 909 518 AF Post by: dstamatoiu on August 24, 2013, 01:34:42 PM Hey all,
So I been a lurker on the site for some time now and its time for me to post because I can't seem to find a solution. I picked up a ecu (8E0 909 518 AF) as a spare in my 03 A4 1.8T AWD AUTO/Test cars. So I can play with the ecu without IMMO so I can plug and play between cars. I used ME7_95040 to Read the Eprom for the 95040. I put it on my test bench and threw the ecu into boot mode. I used command m37_95040 -b9600 --bootmode -p 2 -r95040.bin and I get uC identification response =0x00. Unknown ID. Do I need to install a new 95040? Thanks in advance for the help. Title: Re: Strange Error 8E0 909 518 AF Post by: ddillenger on August 24, 2013, 02:34:15 PM 1.31 is relatively straightforward. Try this command:
ME7_95040 --bootmode -rp2 518AF.bin Title: Re: Strange Error 8E0 909 518 AF Post by: dstamatoiu on August 24, 2013, 11:46:19 PM 1.31 is relatively straightforward. Try this command: ME7_95040 --bootmode -rp2 518AF.bin Thanks ddillenger I used the command and I still get the same error. See the attachment. When I use NefMoto Boot mode I get this: Connecting... Starting bootstrap loader upload. Sent bootstrap init zero byte. Sent bootstrap init zero byte. Sent bootstrap init zero byte. Bootstrap loader upload failed. Failed to receive device ID response for init zero byte. Disconnected Disconnected Connecting... Starting bootstrap loader upload. Sent bootstrap init zero byte. Received device ID response for init zero byte. Successfully uploaded bootstrap loader. Received bootstrap loader started status message. Starting upload of bootmode runtime. Uploaded bootmode runtime data. Sent baud rate detection byte. Bootmode runtime upload failed. Failed to receive baud rate detection response message. Disconnected Connecting... Starting bootstrap loader upload. Sent bootstrap init zero byte. Sent bootstrap init zero byte. Sent bootstrap init zero byte. Bootstrap loader upload failed. Failed to receive device ID response for init zero byte. Disconnected Connecting... Starting bootstrap loader upload. Sent bootstrap init zero byte. Sent bootstrap init zero byte. Sent bootstrap init zero byte. Bootstrap loader upload failed. Failed to receive device ID response for init zero byte. Disconnected Title: Re: Strange Error 8E0 909 518 AF Post by: littco on August 25, 2013, 01:37:02 AM Thanks ddillenger I used the command and I still get the same error. See the attachment. When I use NefMoto Boot mode I get this: Connecting... Starting bootstrap loader upload. Sent bootstrap init zero byte. Sent bootstrap init zero byte. Sent bootstrap init zero byte. Bootstrap loader upload failed. Failed to receive device ID response for init zero byte. Disconnected Disconnected Connecting... Starting bootstrap loader upload. Sent bootstrap init zero byte. Received device ID response for init zero byte. Successfully uploaded bootstrap loader. Received bootstrap loader started status message. Starting upload of bootmode runtime. Uploaded bootmode runtime data. Sent baud rate detection byte. Bootmode runtime upload failed. Failed to receive baud rate detection response message. Disconnected Connecting... Starting bootstrap loader upload. Sent bootstrap init zero byte. Sent bootstrap init zero byte. Sent bootstrap init zero byte. Bootstrap loader upload failed. Failed to receive device ID response for init zero byte. Disconnected Connecting... Starting bootstrap loader upload. Sent bootstrap init zero byte. Sent bootstrap init zero byte. Sent bootstrap init zero byte. Bootstrap loader upload failed. Failed to receive device ID response for init zero byte. Disconnected I think the eeprom might be knackered like you say.. I had a similar issue on again a 8e ecu I ended up swapping the chip from another ecu and it worked fine... Title: Re: Strange Error 8E0 909 518 AF Post by: dstamatoiu on August 25, 2013, 11:32:43 AM I think the eeprom might be knackered like you say.. I had a similar issue on again a 8e ecu I ended up swapping the chip from another ecu and it worked fine... Thank you littco.. I have some spare 29F800 and 95040 laying around. I will just go out and buy another ecu and clone the eeproms. Thanks again. Title: Re: Strange Error 8E0 909 518 AF Post by: dstamatoiu on August 25, 2013, 01:57:44 PM Ah, dont mind this thread. Close it by all means. I found out that my 21 pin was not getting 12 volt. I fixed the problem and I got the dump...
|