|
Title: Problem with read flash Nefmoto flasher. SECURED FILE? Post by: alizczewy on November 07, 2013, 08:38:03 AM Hi Guys;
I'm trying read flash from Ibiza Cupra '02 me7.5 6K0906032 AQX, but i have problem. I use VAG KKL on FTDI. Nefmoto conected with ECU in KWP 2000 baudrate 52800 Fast Init, read Ecu Info sucesfully. But when i chose memory layout (29f400BB) and push button,, Full Flash Ecu" I saw it (screenshot). Is possible that tuner secured ECU against flash read via OBD??? Title: Re: Problem with read flash Nefmoto flasher. SECURED FILE? Post by: TCSTigersClaw on November 22, 2013, 12:23:15 AM Maybe its a se secured file yes. I would try to read in different baudrates /slow init too
Title: Re: Problem with read flash Nefmoto flasher. SECURED FILE? Post by: ddillenger on November 22, 2013, 12:49:49 AM Look at the calibration data. It's a tuned file, I'd bet it's protected.
Title: Re: Problem with read flash Nefmoto flasher. SECURED FILE? Post by: alizczewy on November 28, 2013, 09:50:13 AM You're right ddillenger File is tuned. No cat, evap, sai, rear O2 etc...aaa and no immo.
Now I swap turbo from S3 and would like change a few things. Is any way (via OBD, because i dont have programmer) to read a secured ECU? Maybe Boot Mode? Regards ;D Title: Re: Problem with read flash Nefmoto flasher. SECURED FILE? Post by: EAG4Racing on December 10, 2013, 11:40:04 AM Hello there!
I just tryied to full read my ECU with NefMoto VW Audi ME7 Flasher Logger 1.9.3.2 but I am getting: 10/Dec/2013 12:25:04.254: LOG: Sent message with service ID RequestUpload 10/Dec/2013 12:25:04.264: LOG: Received message with service ID: NegativeResponse 10/Dec/2013 12:25:04.279: LOG: Received negative response for service ID: RequestUpload, with response code: ServiceNotSupported 10/Dec/2013 12:25:04.288: USER: Validation failed, ECU reports RequestUpload service is not supported. RequestUpload may have been disabled by aftermarket engine software. Does this means I won't be able to extract my bin file not even with boot mode? will try it later today.... Title: Re: Problem with read flash Nefmoto flasher. SECURED FILE? Post by: oldcarguy85 on December 10, 2013, 12:22:39 PM boot mode with galletto should read these files without a problem.
Title: Re: Problem with read flash Nefmoto flasher. SECURED FILE? Post by: EAG4Racing on December 10, 2013, 04:00:12 PM Thank you.
I am doing it right now. I don't know how to ground the pin since is not removable and I need to do it car connected. Should I do it manually? suggestions please. Title: Re: Problem with read flash Nefmoto flasher. SECURED FILE? Post by: oldcarguy85 on December 11, 2013, 05:24:33 AM What do you mean it is not removable?
Title: Re: Problem with read flash Nefmoto flasher. SECURED FILE? Post by: EAG4Racing on December 11, 2013, 08:32:26 AM Well I mean the chip isn't removable. I tried to do the boot mode procedure but no luck.
Since I don't have a bench harness I did it while connected to the car! Any way did not work galleto said BOOT MODE INACTIVE What I didn't do was to unplug battery before grounding pin don't know if that make a difference? Title: Re: Problem with read flash Nefmoto flasher. SECURED FILE? Post by: oldcarguy85 on December 11, 2013, 09:19:44 AM Well I mean the chip isn't removable. I tried to do the boot mode procedure but no luck. Since I don't have a bench harness I did it while connected to the car! Any way did not work galleto said BOOT MODE INACTIVE What I didn't do was to unplug battery before grounding pin don't know if that make a difference? You need to leave ignition on and disconnect battery. Then connect battery power while you are grounding the pin. The ECU still has power even with the ignition off. Title: Re: Problem with read flash Nefmoto flasher. SECURED FILE? Post by: EAG4Racing on December 11, 2013, 10:12:12 PM Hey thank you I will try it tomorrow morning!
That's a great news for me! Thx |