|
Title: 06a906032 HS Bricked? Help Post by: brokenvespa on January 05, 2014, 12:48:48 PM I have successfully pulled the file ith nefmoto and myt vcds cable. Loaded file and definition file into tunerpro.
Set CDSLS - Eurobyte (self explanatory) CLASLVE - Plug CLASLPE - Pump plug To zero to delete SAI. I did not correct check sums. I did need to do that for these corect? Flashed the file back to my ecu. Car started once and ran for awhile. Turned car off. Now car wont start and I am unable to get into ecu with nefmoto or VCDS. Swapped ecu wih another just to make sure it is an ecu issue. New ecu reads fine. Reinstalled old ecu and I can now communicate with VCDS. Tried to get back in with Nefmoto and it is reporting a security issue. Is referring to the immoblizer? I kinda remember reading somewhere here that nefmoto does not like it when immoblizer is on. Is this correct? can I immo off my 95040 chip ( I can do this successfully) and flash the original file or a check sum corected file or do I need a cable to use galletto software to recover? If I unplug the ecu for a miniute or so and plug back in I can get into the ecu with VCDS once until I try to start car the nothing. Help? Thank you Title: Re: 06a906032 HS Bricked? Help Post by: gigabyte on January 05, 2014, 01:32:07 PM Hi
Yeah you should check the checksums anytime you alter your tune. My advice would be to use a MPPS V12 and re flash the ECU. This should bypass the security and get you back up and running. Title: Re: 06a906032 HS Bricked? Help Post by: ddillenger on January 05, 2014, 02:39:43 PM No need for MPPS. Just disconnect the battery for 30 minutes, then connect with nefmoto and reflash a file with proper checksums.
Title: Re: 06a906032 HS Bricked? Help Post by: brokenvespa on January 05, 2014, 02:48:02 PM Yea, halfway through the flash I realized I did not do anything with the check sum. I know better. Does anyone have a freeware solution that I can use my vcds cable with?
Title: Re: 06a906032 HS Bricked? Help Post by: fknbrkn on January 05, 2014, 03:11:55 PM you can post your file in "Checksum update request" forum
and someone helps you or get MTX Electronics checksum plugin for TunerPro ( $10 ) Title: Re: 06a906032 HS Bricked? Help Post by: brokenvespa on January 05, 2014, 03:47:50 PM ok , when ecu is unplugged for a bit Nefmoto will try to connect but gettng error message that ecu prerequisites not met. Immoblizer not matched .Should I immo off this ecu then try again? mY soldering station and chip burner are at work and I was hoping to not have to open up ecu or bench flash since I have not built a bench harness yet.
Title: Re: 06a906032 HS Bricked? Help Post by: ddillenger on January 05, 2014, 03:52:10 PM You have to flash in car. If you don't, you have to immo-off. If you're going to bootmode to immo off (using argdubs tool) you might as well just bootmode flash a good file with galletto.
Title: Re: 06a906032 HS Bricked? Help Post by: brokenvespa on January 05, 2014, 04:20:52 PM I do want to flash in the car. My problem at hand is with getting Nefmoto to flash then. It is not happy with my immoblizer.
Any suggestions ? Im using 29F800 memory layout. First time I did this, It read and wrote perfect. Title: Re: 06a906032 HS Bricked? Help Post by: jaymk89 on January 17, 2014, 09:22:40 AM Brokenvespa,
Did you ever get anywhere with this, I have had the exact same issue as yourself today on my ME7.5 06A906032DR where I cannot access the ECU anymore after a successful map and the car won't start! Jay Title: Re: 06a906032 HS Bricked? Help Post by: darkshado87 on January 17, 2014, 11:24:58 AM Had the same issue bootmode immo off the 95040 then bootmode the correct checksumed file should be fine. If you need your files checksumed I can give you the direct download link for winols that has me7 checksum plug in for free. I also have a bad ass 032hs file with full deletes that I have worked on now for a while Id be happy to let you run.
Title: Re: 06a906032 HS Bricked? Help Post by: adam- on January 17, 2014, 03:50:09 PM Post the file and def! :)
Title: Re: 06a906032 HS Bricked? Help Post by: brokenvespa on February 01, 2014, 04:55:14 PM I have not worked on this problem yet. I did Immo off the ecu and I was still getting the same error. I have another ecu and just have not made the time to get into the ecu with galletto. I wanted to build a bench harnes, just need to get some sort of power supply. I will post results when I figure it out.
|