|
Title: flashing problem..now cannot connect to ecu Post by: urquattro on February 14, 2014, 03:55:59 PM hi guys
i used this software 3x before and worked great... using ross-tech registered cable tried to flash this car i got done reading the ecu and saved the file in case of something... went into flashing the ecu with my new file and it started to do it then got a msg that cannot clear memory and one more msg dont recall what software said nefmoto closed connection now i cannot communicated or even connect via nefmoto any ideas? its a 2000 audi a6 4.2 i am working on thanx in advance Title: Re: flashing problem..now cannot connect to ecu Post by: _nameless on February 15, 2014, 05:13:09 AM hi guys disconnect neg battery terminal then step on the brake a few times (this kills saved power in the electronics) then reconnect the battery and see if your ecu is live... If not then hope you have an alternative for recovery i used this software 3x before and worked great... using ross-tech registered cable tried to flash this car i got done reading the ecu and saved the file in case of something... went into flashing the ecu with my new file and it started to do it then got a msg that cannot clear memory and one more msg dont recall what software said nefmoto closed connection now i cannot communicated or even connect via nefmoto any ideas? its a 2000 audi a6 4.2 i am working on thanx in advance Title: Re: flashing problem..now cannot connect to ecu Post by: urquattro on February 18, 2014, 10:28:50 AM so i got finally the ross-tech to work with galletto program
i get the ecu to work in boot mode galletto starts erasing ok starts writting after little bit tells me error writting any ideas?? thanx Title: Re: flashing problem..now cannot connect to ecu Post by: ddillenger on February 18, 2014, 11:31:45 AM Pic of the inside of the ecu?
Title: Re: flashing problem..now cannot connect to ecu Post by: urquattro on February 18, 2014, 12:33:53 PM not sure if the issue i am having is with selecting the ecu
i select ----boot mode--- audi vw me 7.x.x 29f800bb ( ground eprom pin 24 ) all works seeding ok, erasing ok, just when it starts to write takes a little bit, no percentage of writting happens and give error msg of writting error i am doing it in the car since i do not have a bench power supply, but the battery is fully charged and i have a battery charger on it with voltmeter @ 13.8 with ignition turned already on.... http://i129.photobucket.com/albums/p204/tomask2/Auto%20Parts%20For%20Sale/20140218_111151_resized_zpsb42a0e9f.jpg (http://i129.photobucket.com/albums/p204/tomask2/Auto%20Parts%20For%20Sale/20140218_111151_resized_zpsb42a0e9f.jpg) http://i129.photobucket.com/albums/p204/tomask2/Auto%20Parts%20For%20Sale/20140218_111200_resized_zps79ca1ca8.jpg (http://i129.photobucket.com/albums/p204/tomask2/Auto%20Parts%20For%20Sale/20140218_111200_resized_zps79ca1ca8.jpg) Title: Re: flashing problem..now cannot connect to ecu Post by: prj on February 18, 2014, 01:12:50 PM Run direct k-line to ecu.
Title: Re: flashing problem..now cannot connect to ecu Post by: urquattro on February 18, 2014, 01:17:58 PM ok
how do i do that? and can i do this since i am trying to flash in car? Title: Re: flashing problem..now cannot connect to ecu Post by: urquattro on February 19, 2014, 09:35:35 AM so i find that this ecu is actually a me 7.1
is there a way to use galletto to boot mode and write the file in the car i only see a boot mode write file for 7.1.1 thanx Title: Re: flashing problem..now cannot connect to ecu Post by: nyet on February 19, 2014, 09:49:20 AM bootmode 7.1 and 7.1.1 are the same
Title: Re: flashing problem..now cannot connect to ecu Post by: urquattro on February 19, 2014, 09:54:29 AM strange why it does not want to write then...
everything works in boot mode just writting does not start... |