|
Title: G-box bin on D-box car Post by: armageddon on March 10, 2014, 04:21:34 PM Hi, I plan to run my G-box bin on a S4 with D-box ECU
This is what I changed: MAF: MLOFS 0.00 kg/h to 200.00 kg/h KFKHFM with D-box values MLHFM with D-box values Rear O2: CDKAT = 0.00 CWDLSAHK = 0.00 CDHSHE = 0.00 CDHSH = 0.00 CDLATV = 0.00 CDLASH = 0.00 CDLSHV = 0.00 CDLSH = 0.00 CWKONLS = 1.00* after correction = 17.00 CLRHK = 73.00 ESKONF 0x10c87 from F3 to FF Is this correct? Am I missing something? best regards Title: Re: G-box bin on D-box car Post by: prj on March 10, 2014, 04:25:13 PM First try crossflashing and see if it even boots.
Title: Re: G-box bin on D-box car Post by: ddillenger on March 10, 2014, 04:29:51 PM You cannot set CWKONLS to 1. You will have malfunction codes. 1=single precat o2 sensor! 17=dual precat o2 sensors.
Title: Re: G-box bin on D-box car Post by: armageddon on March 10, 2014, 04:32:01 PM First try crossflashing and see if it even boots. sorry, but realy don´t understand what you mean ??? try flash g-box on d-box to make sure it is possible?? Title: Re: G-box bin on D-box car Post by: armageddon on March 10, 2014, 04:35:57 PM You cannot set CWKONLS to 1. You will have malfunction codes. 1=single precat o2 sensor! 17=dual precat o2 sensors. ok, thanks Title: Re: G-box bin on D-box car Post by: Snow Trooper on March 11, 2014, 11:49:49 AM You cannot set CWKONLS to 1. You will have malfunction codes. 1=single precat o2 sensor! 17=dual precat o2 sensors. and it will only trim one bank Title: Re: G-box bin on D-box car Post by: armageddon on March 11, 2014, 03:51:40 PM I read s4wiki again and now I understand that. language could be a barrier sometimes
assuming that I can crossflash G-box to D-box those steps (maf convertion and rear o2 delete) will be enough? Title: Re: G-box bin on D-box car Post by: ddillenger on March 11, 2014, 03:56:09 PM Yes, but you must make sure the addresses are correct. They are not the same as what is in the wiki.
Title: Re: G-box bin on D-box car Post by: armageddon on March 11, 2014, 04:33:40 PM I use a G-box xdf from nyet page, and for ESKNOF have seen a post over here how to locate it and find out that start at 0x10c81. Then I change byte 6 (0x10c87) from F3 to FF.
I will give it a try and let you guys know thanks Title: Re: G-box bin on D-box car Post by: armageddon on April 23, 2014, 02:26:00 PM Update
My friend received ECU today and he is having this fault codes: 18058 powertrain data bus p1850 35 00 missing message from instrument cluser 17530 oxygem(lambda) sensor heating b2 s2 p1122 35 00 open circuit For 18058 I think he have to change channel 60 to 0, and what about 17530? I think I remove them correctly ??? edit: also, idle is a litle rough Title: Re: G-box bin on D-box car Post by: armageddon on April 24, 2014, 03:54:03 PM So, changing channel 60 didn't solve "18058 - Powertrain Data Bus", I am assuming that I need to change CW_CAN_R from 36 to 4 as softcoding is 05711(euro3/esp)
For Rear O2 I only changed ESKONF[6], do I need to change ESKONF[5] too? Title: Re: G-box bin on D-box car Post by: armageddon on April 25, 2014, 06:53:27 AM I tryed on my car(original G-box) disconected rear O2 and I'm getting the same error: 17530 oxygem(lambda) sensor heating b2 s2
p1122 35 00 open circuit I followed every steps on wiki and also change ESKNOF[5] from 00 to 0C, didn't do it before, but I cannot get rid of that fault code. Any ideas? Title: Re: G-box bin on D-box car Post by: ddillenger on April 25, 2014, 08:27:52 AM Post your file.
Title: Re: G-box bin on D-box car Post by: armageddon on April 25, 2014, 08:53:17 AM Here is the file with rear o2 deleted
Title: Re: G-box bin on D-box car Post by: ddillenger on April 25, 2014, 09:28:18 AM 10C86
0C--->CC Title: Re: G-box bin on D-box car Post by: armageddon on April 25, 2014, 10:34:50 AM Thanks, that works (as you already know :) )
I was looking at it again and I notice that I made a mistake, I change 00 to 0C instead of C0 :-[ Another silly question, should I put C0 or CC, as the original is 00? |