NefMoto

Hello...
i am from Athens, i read a lot of your post here and i see that here are people how know a lot about ecu tuning and i need your help.
 i have an Audi S3 8p manual gearbox and i saw this video on youtube https://www.youtube.com/watch?v=67_SMqiGXxk
i study a lot and i saw that the wire changes are few ( my car need only 2 lines the one that connect the shift box and the line that give power to the mechatronic ecu )
few e -mail with compsport in Poland ( they swap the gearbox  on 7 cars, but the information that they share with me were little and they did not respond to all e -mails to give me information )
My problem is that i have done with all parts and i don't know how to code the ecu ( compsport told me that they will code my ECU  but now they do not respond to my messages :/  ) 
Here in Greece they don't know what to do, so i start searching how to code it to dsg!!!!! according to compsport it is very easy to code the ecu. i also have a friend from England that we are in the same position,he is also asking people there if they know how to code the ecu
does anyone know anything that could help me???

thanks

What is Your actual coding in ECU ? You use VCDS ?

i have vcds 805 but i can't change the coding ( error 31 request out of range )
compsport told me that i should go to my tuner to code the ecu and that i can't code it with vas pc or vcds!! you are from Poland so you must know them ( thanks for your reply :)   )
you want to find my actual coding?i can if this will help you

Yes I know them , I also have swaped TSI engine with DSG transmision to A3 8P from 2004 . Put here actual coding readed with VCDS and Coding that You have tried and it won't accept it.
Can You connect to dsg ? From waht Year is Your S3?

good so you are famirial with this swap, i am glad :)
my car is 10/2007 and yes i can connect to to dsg 's mechatronic ( i don't have the gearbox yet i am trying to find one used, but i have a friends mechatronic )
i don't know all the bit tha i have to change coding...
at 01 Engine
current coding :  01030003180F0160
new coding     :  010300031C0F0160
for the new coding i have an error 31

16- Steering wheel
current coding : 0000042
new coding     : 0013142

at 02 Auto trans i have access but it doesn't saw an info ( register version only ) i have some notes that said to change code to the cluster but i don't have access,also these notes said to change code in  19 can gatway but there is no bit for transmition

           Address 01: Engine
Control Module Part Number: 8P0 907 115 H
  Component and/or Version: 2.0l R4/4V TFSI     0050
           Software Coding: 01030003180F0160
            Work Shop Code: WSC 00191

Advanced Identification
     Serial number: AUX7Z0G5FNQ12K
     Identification: BPG-810
     Revision: 5BH16---
     Date: 30.05.07
     Manufacturer number: 0790
     Test stand number: 1850
Flash Status
     Programming Attempts: 84
     Successful Attempts: 82
     Programming Status: 00000000
     Required Conditions: 00000000
Software
     A000
     A4.8.6
Misc.
     Hardware number: 8P0 907 115 B
     Immo IV Challenge: 23 B7 B3 53
Car Info
     Chassis Number: WAUZZZ8P48A025649
Saturday,03,May,2014,18:02:24:26365
VCDS Version: Release 805.1
Data version: 20080823

By experience it's always better to recode the network controller first. In that case it may not answer 19, so when 19 doesn't answer you have it in 17 adaptation. In Powertrain installation list. Code the network Master with what you have in the car. That way all other controllers will want to recode more easily.

Hey,

did you find any solution for this problem now? I´ve the same problem and as far as I know the ECU needs to be coded in EEprom. There must be the "bit" for the Manual to DSG.
I´ve uploaded the stock bdmtogo read. Maybe somebody can help?

Regards TKrE

Yes you do need to manually do this in eeprom.

good luck with that