|
Title: Immo vw golf problem Post by: gentki on May 12, 2014, 02:55:54 PM hi, I want to delete immo golf IV because the engine will be in a different car. Ecu is 06A 906 0 32 MJ. I am using the tools Argdub and I have a problem.
(http://www.iv.pl/images/61829153743914178710_thumb.jpg) (http://www.iv.pl/viewer.php?file=61829153743914178710.jpg) Please help what is the problem Title: Re: Immo vw golf problem Post by: ddillenger on May 12, 2014, 03:41:49 PM What cable is it?
Post a screenshot in device manager please. Title: Re: Immo vw golf problem Post by: oldcarguy85 on May 12, 2014, 04:06:10 PM Did u put the ecu in boot mode?
Title: Re: Immo vw golf problem Post by: _nameless on May 12, 2014, 04:48:55 PM try obd2 read
Title: Re: Immo vw golf problem Post by: gentki on May 13, 2014, 06:57:31 AM I use vag k + can 3.6
(http://www.iv.pl/images/44529031911370882511_thumb.jpg) (http://www.iv.pl/viewer.php?file=44529031911370882511.jpg) (http://www.iv.pl/images/44327299678973639724_thumb.jpg) (http://www.iv.pl/viewer.php?file=44327299678973639724.jpg) I also have VAG 409.1, but I get an error when I use 0x08. I'm trying to boot mode, ground pin 24 with a resistor 1kohm for 5-10 seconds Title: Re: Immo vw golf problem Post by: oldcarguy85 on May 13, 2014, 10:18:09 AM I use vag k + can 3.6 Process to get into boot mode should be...(http://www.iv.pl/images/44529031911370882511_thumb.jpg) (http://www.iv.pl/viewer.php?file=44529031911370882511.jpg) (http://www.iv.pl/images/44327299678973639724_thumb.jpg) (http://www.iv.pl/viewer.php?file=44327299678973639724.jpg) I also have VAG 409.1, but I get an error when I use 0x08. I'm trying to boot mode, ground pin 24 with a resistor 1kohm for 5-10 seconds 1. power off ecu 2. ground pin 24 3. power on ecu 4. wait 3-5 seconds and remove pin 24 ground Is this the procedure u r following? Title: Re: Immo vw golf problem Post by: gentki on May 13, 2014, 11:26:10 AM I use this method and I get an error. OBD also does not work
(http://www.iv.pl/images/18088984551056397470_thumb.jpg) (http://www.iv.pl/viewer.php?file=18088984551056397470.jpg) plugged k line ECU pin 43 pin cable 7 ECU ground pin 1 and cable pin 5 and ground with a resistor to Bootmode 12 ECU pin 3 and 62 cable pin 16 (I use the charger) Title: Re: Immo vw golf problem Post by: _nameless on May 13, 2014, 10:15:56 PM Id say the cable you have is not supported by argdubs tool. take a pic of the cable you are using and upload
Title: Re: Immo vw golf problem Post by: gentki on May 14, 2014, 02:09:50 AM when I use this cable http://www.lightinthebox.com/pl/vag-k-can-commander-3-6-skaner-dla-audi-vw-obd2_p356250.html I get error 0x07
when i use this cable http://www.lightinthebox.com/pl/System-OBD2-OBD-II-USB-KKL409-1-VAG-COM-409_p39973.html?pos=ultimately_buy_11 i get error 0x08. on this side http://nefariousmotorsports.com/forum/index.php?topic=1168.0 of the s-company had the same problem and on the next page argdub wrote that the ECU reset in Bootmode, but how? Title: Re: Immo vw golf problem Post by: _nameless on May 14, 2014, 07:19:19 AM when I use this cable http://www.lightinthebox.com/pl/vag-k-can-commander-3-6-skaner-dla-audi-vw-obd2_p356250.html I get error 0x07 none on that page has had the same issue as you... arg dubs tool is not getting a response from your cable... thats the trouble your having. Vag k can commander uses ft23 chip i not sure why it didnt work. I have had 3 cables that ive had to use with argdubs tool, first was galletto 1260 cable and it worked fine (until it stopped working bad solder connections). the second cable was just a ebay special and I only had one successful write with that cable. No matter what rate I tryed to connect at it always failed. Third and last cable works flawlessly and is identical to the second one that I ordered... when i use this cable http://www.lightinthebox.com/pl/System-OBD2-OBD-II-USB-KKL409-1-VAG-COM-409_p39973.html?pos=ultimately_buy_11 i get error 0x08. on this side http://nefariousmotorsports.com/forum/index.php?topic=1168.0 of the s-company had the same problem and on the next page argdub wrote that the ECU reset in Bootmode, but how? Title: Re: Immo vw golf problem Post by: gentki on May 14, 2014, 07:26:13 AM that is, the cables are not good... What cables works well with this?
Title: Re: Immo vw golf problem Post by: _nameless on May 14, 2014, 07:34:24 AM this is what im using now
http://www.ebay.com/itm/New-USB-OBD-II-2-KKL-409-1-OBD2-Cable-VAG-COM-409-FT232RL-Chip-Support-Win7-Win8-/281330054083?hash=item418093f3c3&item=281330054083&pt=Motors_Automotive_Tools&vxp=mtr Title: Re: Immo vw golf problem Post by: _nameless on May 14, 2014, 07:38:04 AM the only other thing that you could try is change broad rate start at 9600
Title: Re: Immo vw golf problem Post by: gentki on May 14, 2014, 12:38:54 PM My one cable "blue" is on the chip 232Bm, I understand that your cable on the chip 232RL works ok with ardub tools.
when the ECU was in the car with no problem this cable to connect to the read error, it is no longer on the table |