|
Title: SAI/MSLUB Post by: em.Euro.R18 on September 22, 2014, 09:34:12 AM I've come up with a P1423 using the XDF provided. SAI insufficient flow I'm not sure if my XDF has MSLUB and I cannot seem to find a similar xdf or kp that includes MSLUB to compare in OLS. ???
bin file and my own extended version of your XDF are attached. Also would like to suggest to those using LAMFA as for WOT fueling not to forget to add appropriate changes in KFWDKSMX. warning DO NOT USE THIS FILE TO FLASH this file for the spectators downloading it. Title: SAI/MSLUB Post by: metronet on September 22, 2014, 01:50:48 PM bin file and my own extended version of your XDF are attached. I recently followed the s4wiki to set MSLUB/MSLBAS on my M/L box and was able to allow the SAI readiness to run and pass. However, the same definition shows a small offset with your BIN. Is the 551T bin you attached from a A6 by any chance? See screenshot for the offset: (http://i.imgur.com/Wac8CY2.png) Attached is the M-box definition I used (based on the standard M definition from the wiki) plus a few other things like "dwell time" if you're running 2.0T coils. Title: Re: SAI/MSLUB Post by: nyet on September 22, 2014, 03:29:42 PM I've come up with a P1423 using the XDF provided. SAI insufficient flow I'm not sure if my XDF has MSLUB and I cannot seem to find a similar xdf or kp that includes MSLUB to compare in OLS. ??? bin file and my own extended version of your XDF are attached. Also would like to suggest to those using LAMFA as for WOT fueling not to forget to add appropriate changes in KFWDKSMX. warning DO NOT USE THIS FILE TO FLASH this file for the spectators downloading it. The stage 1 XDF is only for tutorial purposes and SPECIFIC to the stage 1 effort. SAI issues are not a part of that effort. I have removed that XDF from the OP. Title: Re: SAI/MSLUB Post by: metronet on September 22, 2014, 03:56:22 PM Thanks for moving this nyet.
I was worried that my reply would be off-topic since the OP's bin attached doesn't appear to be a M-box which is what the stage 1 project is really aiming for. Title: Re: SAI/MSLUB Post by: em.Euro.R18 on September 30, 2014, 03:57:06 PM Yes it is an a6 tiptronic bin and it should be offset from M box. I have read that MSLBAS should be set to O, factor is .4 for that scaler but as of right now I'm getting a value of 13.20 for MSLBAS should I convert to hex and "00"? so far the codes are P1131 P1423 P1141
Does the screen shot above show the correct offset with correct values for MSLUB? Title: Re: SAI/MSLUB Post by: em.Euro.R18 on October 01, 2014, 06:17:58 AM (https://fbcdn-sphotos-h-a.akamaihd.net/hphotos-ak-xap1/v/t1.0-9/1970630_903733909919_3432515373015066043_n.jpg?oh=7cffa4db8274305a25e77ccfb01366c4&oe=54C5D4B4&__gda__=1421735148_417ce8f87d15c56e2976644abb120a0c)
This is what I'm looking at now. For some reason the address offset for battery voltage shifted -4 when I opened up my XDF axis values right now are 0.0 0.0 .7 3.52 7.05 10.57 14.09 17.62 for MSLUB Also I've found CDSLS at 181b0 but have yet to find one XDF or ols map pack with CWKONABG on any ecu to give me a general idea of where it would be. if anyone can give me a tip that would be great. Appreciate all the help guys as usual Title: Re: SAI/MSLUB Post by: antoffka666 on February 05, 2015, 11:57:39 PM (http://s017.radikal.ru/i437/1502/68/3591fde3ee7b.jpg) (http://www.radikal.ru)
Hi! please help find my address in xdf |